PDA

View Full Version : Fiat HIGH CD HC11PA8 Cancheck?


magdex
24th October, 2009, 02:01 PM
Pleasee Disable Cancheck and red Orginal CODE

I dont know if EEPROM DUMP is Correct !
7 641 376 316
815 BP137623299565

Read by MotoCracker 6.2

NYO4 Can't do that

Regards !
jokersat
24th October, 2009, 05:19 PM
code in MCU HC11PA8
lupu_sandu
25th October, 2009, 12:18 PM
FIAT PUNTO HIGH CD
7 641 376 316
e1 021613 CE
BP1376
Portugal

Code is stored on MCU Motorola HC11PA8 on QFP64 socket
connection points for programming is stored on Images section
resonator is neccessary replace with 8MHz for r/w time
From Nyo4
magdex
25th October, 2009, 02:24 PM
I know ! I read it and send dump in First post 1
But Nyo can't read code or dump is incorect or mew algo

Please confirm is dumpe is corect ?
magdex
25th October, 2009, 06:57 PM
Solved

thx all

regards
wilcoboy
25th October, 2009, 10:36 PM
Solved

thx all

regards

Please write us how you fix the problem?
Calculator? or another dump?

Thanks !
djdansmart
26th October, 2009, 10:21 AM
Please write us how you fix the problem?
Calculator? or another dump?

Thanks !


What you need to know exactly? Is verry easy to remove cancheck!!
PremierD
26th October, 2009, 11:24 AM
What you need to know exactly? Is verry easy to remove cancheck!!

Remove compleatly ...? so that it can be used in another vehicle....? or to enable you to check the code on the bench pror to refiting in vehicle....?
magdex
26th October, 2009, 12:01 PM
Yes it's easy ! If you have programmer can read MCU PA8 without desoldering ! I Remove MCU and read it by ETL programmer .
USE NYO4 to remove all security and works OK ! (Change only 4 bytes)

Regards !
PS . I try read by MotorolaCracker 6.2 conect OK MCU is boot ok but read was wrong .
wilcoboy
26th October, 2009, 12:31 PM
Thank you for your answers try NYO4. Tell the result.
Only the first that I find NYO4...

Regards!
--------------------------
Today try Nyo4 not open file !
Nyo you can delete cancheck or not .
How to use Nyo4 whether a dongle protection or not ?
Is there any other software ?

Regards !
magdex
26th October, 2009, 10:03 PM
Send me your File i Prepare for you and you can see change in dump !
wilcoboy
26th October, 2009, 10:32 PM
Work!!! I finally understand!

Thank you very much, Magdex.

Problem solved.
magdex
26th October, 2009, 10:40 PM
OK !

Regards
djdansmart
27th October, 2009, 09:37 AM
Yes it's easy ! If you have programmer can read MCU PA8 without desoldering ! I Remove MCU and read it by ETL programmer .
USE NYO4 to remove all security and works OK ! (Change only 4 bytes)

Regards !
PS . I try read by MotorolaCracker 6.2 conect OK MCU is boot ok but read was wrong .


Next time use motocracker 4.3! Whit 6.2 i have same problems..!
magdex
27th October, 2009, 10:20 AM
Ok Can send Version 4.3 I can't Find in my HardDrive ?
mikemike
27th October, 2009, 10:30 AM
Hi!

here's............
magdex
27th October, 2009, 10:49 AM
THX !

regards
afonsom
23rd June, 2010, 10:01 AM
Hi people,

I have the same problem in my Punto's Blaupunkt radio, and I've been reading forum to know how to solve it. But, I'm a geek in this kind of things.

Can you please tell me wich hardware will I need to use EEPROM's readers and programmators? Where can I found it?

In Portugal, Blaupunkt remove CANCHECK by paying 35 euros. Is this process more or less expensive?

Thanks in advance