2006 Civic S93C76 Cannot write?

[bulletboltb]

Hello everyone,

I have just faced silly problem, took chip out from dash, read as IS93C76A SOIC8 all came up good, but when I try to write gives error and all it writes into chip is 02 03 ? Anyone had similar issue?

[brend]

What programmer you use.?

[bulletboltb]

I use minipro

[brend]

I use minipro


Try this...........

[ascrap2003]

How is eeprom connected to minipro? Are you using soic to dip socket? Pin 1 in proper position?

[bulletboltb]

Programmed successfully. I'll try to solder it back and see if it works. But what's the reason of using different chip id? Shouldn't it work under manufacturer's code? Thank you by the way, owe you a pint!

[brend]

Hello everyone,

I have just faced silly problem, took chip out from dash, read as IS93C76A SOIC8 all came up good, but when I try to write gives error and all it writes into chip is 02 03 ? Anyone had similar issue?

NEXT TME.......... IS93C76A (X16)..........:glee:

[ascrap2003]

Programmed successfully. I'll try to solder it back and see if it works. But what's the reason of using different chip id? Shouldn't it work under manufacturer's code? Thank you by the way, owe you a pint!

Make that 2 pints lol, brend what are your toughts on mini I have heard good things about it.

[bulletboltb]

NEXT TME.......... IS93C76A (X16)..........:glee:

I have tried ALL options under ISSI manufacturer 93c76 type chips, none of them worked...

[ascrap2003]

btw if that same as 2007 civic us model i always read & write in circuit no problem, If thats the case idc & ribbon w/ pomona should work I think.

Correction DIP to IDC etc etc

[brend]

Make that 2 pints lol, brend what are your toughts on mini I have heard good things about it.

Like what?

[ascrap2003]

Like what?

Best cheap universal eeprom programmer

[brend]

.....:champions:.....

[ascrap2003]

Ok because I already purchased one lol I really want a beeprog or that other one vp900 or something

[bulletboltb]

tried to fit clocks back in the car, came up with fuel gauge fault, also rpms wont work. Any ideas?

[bulletboltb]

Anyone have a ori file for 1.8 manual civic?

[nikz]

number write <8200 xxxx>

[bulletboltb]

not sure what you're asking?

All data I see on the dash is:

SMG HR0342003
78200 E120

F28D061556015

Edit:
I have downloaded random civic ori file, programmed and works fine except I can't change to miles and outside temp doesn't work. I think it was issue when I read chip with wrong id. Need ori file of same dash if anyone have one? Thanks!

[nikz]

......................................

[bulletboltb]

Your picture shows different panel or different model clocks..

[ascrap2003]

Your picture shows different panel or different model clocks..
Heres what should be a 07 scratch that dnt have one.

[bulletboltb]

no idea what you mean?

[ascrap2003]

no idea what you mean?
Tought I had a 07 Manual Dump but its Auto I do have a 2010 SI 5 Spd Dump If That Helps But I dont think it does

[bulletboltb]

I have tried many dumps >2007 models, none of them works..

[ascrap2003]

Are you sure your soldered eeprom back properly?

Is milage displayed and counting? Could also be you knocked something loose, dirt, sweat a bunch other things. When it comes to electronics a sneeze at the wrong time can cause havoc! lol

I would double and triple check. I've only been in bizz a lil over a year and 9 out of 10 times I have had an issue its my error.

Solder iron tip size, approach, solder wire type & size, cleaning & prep etc.

I have gotten much better but just like anything else your always learning.

On another note my eyesight is horrible I had a burnt pad right in front of me a few weeks ago. lol

[bulletboltb]

Appreciate your suggestions mate.

The problem is that I have read eeprom using wrong chip ID, so I no longer have original file from my car. I have found something close - shows mileage, fuel level, rpm, but I get other types of errors on the dash. I'll borrow another dash from scrapyard and get the dump of it as it looks no one here have one.



If anyone comes to similar position bit info:


If using MiniPro programmer, read with SEIKO S-93C76A (DFJ) @SOIC8

The mileage is stored within (Tachosoft not accurate in this case):
0000C0
0000C8
0000D0
0000D8


My mistake was that I looked for S93C76 and it came up as ISSI manufacturer, but it's SEIKO you are looking for.

Not sure if it can be read with clip (pomona or whatever you use) as I don't have one yet, will update when try it out.

Will upload my file too if thread won't be deleted.

Thanks everyone for help :peaceful:

[narkeleptk]

clips wont work with your Minipro if its the CS version.

[ascrap2003]

clips wont work with your Minipro if its the CS version.

I think mine is a "A" version I read that one is better than other so thats the one I got. I really want a Bee or VP

[bulletboltb]

Anyone can explain how to find out what version I have?

[narkeleptk]

If yours has the openeing on the side for connections then its the A version. if it has sealed up side then its most likely CS

[bulletboltb]

Just looked at mine, there is sticker underneath saying Model TL866CS. Why it won't work with clips?

[narkeleptk]

Pm Ray-Ray he knows all aboit it and how to "fix it"

[juanes 3]

the (https://dictionary.cambridge.org/es/diccionario/ingles-espanol/the) honda the (https://dictionary.cambridge.org/es/diccionario/ingles-espanol/the) epron must (https://dictionary.cambridge.org/es/diccionario/ingles-espanol/must) be (https://dictionary.cambridge.org/es/diccionario/ingles-espanol/be) careful (https://dictionary.cambridge.org/es/diccionario/ingles-espanol/careful) are (https://dictionary.cambridge.org/es/diccionario/ingles-espanol/are) 16 bit (https://dictionary.cambridge.org/es/diccionario/ingles-espanol/bit) mini (https://dictionary.cambridge.org/es/diccionario/ingles-espanol/mini) prog in (https://dictionary.cambridge.org/es/diccionario/ingles-espanol/in) 16bits ok (https://dictionary.cambridge.org/es/diccionario/ingles-espanol/ok) upa care (https://dictionary.cambridge.org/es/diccionario/ingles-espanol/care)