View Full Version : 2005 dodge ram stf9150 mileage correction
gpemporium
21st November, 2017, 06:07 PM
Using a carprog - stf9150
file provided is 168000 miles
need 128500 miles
any help will be thanked
milmilhas
21st November, 2017, 06:16 PM
test plase
momogsm
21st November, 2017, 06:18 PM
.........................................128500 mil ok
milmilhas
21st November, 2017, 06:23 PM
Sorry, I misjudged
momogsm correct
gpemporium
21st November, 2017, 06:23 PM
tested - under the mileage I need but nearly spot on 125000.. thanks anyways
milmilhas
21st November, 2017, 06:24 PM
1128500....
gpemporium
21st November, 2017, 06:25 PM
.........................................128500 mil ok
this shows 168563 .... need 128500 miles
milmilhas
21st November, 2017, 06:27 PM
128500.......
gpemporium
21st November, 2017, 06:36 PM
128500.......
no change in mileage - 168563
ascrap2003
21st November, 2017, 06:57 PM
Algo should be KM / 13.185 = Décimal converted to Hex this is your bottom bytes then ad 1 to every set starting from top bytes down. This will put you within 20 miles
ascrap2003
21st November, 2017, 07:01 PM
I’ll take a look later if you haven’t finished by then, if not showing correctly dump is corrupt .
gpemporium
21st November, 2017, 08:04 PM
I’ll take a look later if you haven’t finished by then, if not showing correctly dump is corrupt .
solved - thank you however - i would like to know the algo on these tho for future reference... feel free to private message me if you have any insight.. we settled with + 250 miles which is not good but passable.... please enlighten me if you have any info
gpemporium
21st November, 2017, 08:13 PM
Algo should be KM / 13.185 = Décimal converted to Hex this is your bottom bytes then ad 1 to every set starting from top bytes down. This will put you within 20 miles
we tested a few files and this seems to be a very good algo. thank you very much
ascrap2003
21st November, 2017, 09:00 PM
I’m sure there’s a better way but this works for me, if not like said dump is corrupt. Are you connecting to legs or pads? I have a pic I’ll post up later for carprog
jomberykaso
21st November, 2017, 09:25 PM
Original Dump is ok, the other dumps posted here with 128.500 miles but spot on 125.000 miles are modifyed with Nyo, that is the problem.
ascrap2003
23rd November, 2017, 09:07 PM
here is the solder pad pinout easy, i use a pencil be gental with pads.
Numbers are for mcu pin reffrence
gpemporium
8th March, 2018, 06:26 PM
I’m sure there’s a better way but this works for me, if not like said dump is corrupt. Are you connecting to legs or pads? I have a pic I’ll post up later for carprog
been connecting to legs using carprog. weve just had a few come back that seems to be due to this issue. we will try your pad setup here in a bit, ill relay the results.
gpemporium
8th March, 2018, 06:32 PM
Does anyone have the power up pinout for this vehicle?
Mikemikemike
10th July, 2019, 09:20 AM
hi you read this with carprog original have clon version and when read say boot error help
robrkl
10th July, 2019, 09:24 AM
hi you read this with carprog original have clon version and when read say boot error help
STOP SPAMMING THE FORUM, SAME QUESTION IN 7 TOPPICS!!!!!!!!!!!!!
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.