Peugeot 206 KM calibration

[3axap]

Hello,

I wanto te recalibrate Dash of Peugeot 206
2004 Model
Made by: Magnetti Marelli
There is NEC inside.

What is the procedure of doing it? I will post the dumps but
dont wanna bother it if it is a hard work to do.

I thought that there is 95xxx inside the dash and it is easy to read them.

Regards

[lupu_sandu]

Read this mate:


Car type: Peugeot 206 (Dash+BSI) - 2002-2006 years
Dash manufacturer is Magneti Marelli/Jaeger, BSI is made by Siemens
Dash chip type is 95020, in BSI you must find 95160
There are 2 known offsets where mileage is stored in dash
type #1
0020: 40 42 0F 00 BF BD F0 FF 40 42 0F 00 BF BD F0 FF
type #2
0010: xx xx xx xx xx xx xx xx 40 42 0F 00 BF BD F0 FF
0020: xx xx xx xx xx xx xx xx 40 42 0F 00 BF BD F0 FF
where the next bytes:
40 42 0F 00 BF BD F0 FF - is a mileage

[3axap]

Thank you for the answer.

"Dash chip type is 95020" - there is not 95020 in the dash:(

[arash1208]

do you have pps ?if you have i can help you

[gps15000]

I have pps. I am interested if you could explain the procedure.
thank you

[biszkopt]

Ihave pps too, can you explain me too?

[gigabyte]

Hello m8s,
can you explain me too ???
Peugeot 206 2003 only NEC in dash no 95020
Help please
Thanks

[drpeter]

Hello m8s,
can you explain me too ???
Peugeot 206 2003 only NEC in dash no 95020
Help please
Thanks


I've done 20X 206's after 2001 and they all had 95020 in Jaeger dash (cluster has two buttons), just remove needles (be carefull they are very tight). Job can be done in 1:15 hrs, BSI 95160 different versions, be aware, if you are not sure what version you have then edit dump manually. One byte wrong and car don't start anymore. Save dumps before doing anything!

Good luck.

[gigabyte]

Here it is what I've got...
So google says that atmel 312 is 24C04.
I don't know what to do.

[PremierD]

Here it is what I've got...
So google says that atmel 312 is 24C04.
I don't know what to do.

Mate an atmel 25020 ... is the same as a ST 95020.... SPI eeproms different manufacturers

PS ..nice clear pickies ...

[gigabyte]

Thanks a lot :)

[gigabyte]

Hello mates,
I do everything like you said. Now when you insert the key and ignition ON display blink 3 times with a value 181300...then it stop blinking and shows the new value. Don't know what I'm doing wrong?
old 173137
new 121056
blinking 181300
Here are the files done by NYO4:

[drpeter]

Hello mates,
I do everything like you said. Now when you insert the key and ignition ON display blink 3 times with a value 181300...then it stop blinking and shows the new value. Don't know what I'm doing wrong?
old 173137
new 121056
blinking 181300
Here are the files done by NYO4:


Very strange looks like your dumps are fine, solderings ok?
dash dump and BSI is ok.

[gigabyte]

Yes I thing soldering OK. I thing is it possible something wrong with BSI dump...
NEY4 erased at 0130 but someone in forum says:

BSI type #5 (2003)
0140: xx xx xx xx xx xx xx xx FF FF FF FF FF FF FF FF
0150: FF FF FF FF xx xx xx xx xx xx xx xx xx xx xx xx
BSI type #6 (2004)
0130: FF FF FF FF FF FF FF FF FF FF FF FF xx xx xx xx
BSI type #7 (2004)
0130: xx xx FF FF FF FF FF FF FF FF FF FF FF FF xx xx

for 2004 erase in 0130 and for 2003 erase in 0140 0150...
my car is 2003. NYO4 recognized correctly old value 173137.

[PremierD]

If you have a look at the "blinking " mileage mate ... There will be a Spanner in front of it .... its the service miles ... Press and hold the trip button and switch on Ignition ... It will count down from 10> =.. release the trip .. ign, off and then back on ....

[drpeter]

If you have a look at the "blinking " mileage mate ... There will be a Spanner in front of it .... its the service miles ... Press and hold the trip button and switch on Ignition ... It will count down from 10> =.. release the trip .. ign, off and then back on ....


Haha I didn't thought about that you are right, job done.

[gigabyte]

If you have a look at the "blinking " mileage mate ... There will be a Spanner in front of it .... its the service miles ... Press and hold the trip button and switch on Ignition ... It will count down from 10> =.. release the trip .. ign, off and then back on ....

YES m8, you are right...I'm feeling ashamed of me :shot:
Thanks

[r6eck]

If you have a look at the "blinking " mileage mate ... There will be a Spanner in front of it .... its the service miles ... Press and hold the trip button and switch on Ignition ... It will count down from 10> =.. release the trip .. ign, off and then back on ....

Got a fair fleg the first time this happened to me and had like 800000 miles :argh:,soon relised it was service mileage

[martin292009]

bin pass the board and the bsi, I do it for you