PDA

View Full Version : Iveco Daily 0281011228 1039S09673



Pyromaniak
14th February, 2018, 08:27 AM
Hi guys, i need ori files, ecu burned. :crushed: Iveco Daily 3,0l 0281011228 1039S09673 F1CE 0481A 50C14HPI EDC16 c8

thanks in advance.

i have some files , but dtc 0010 and limp mode :(

Eight
14th February, 2018, 08:43 AM
0281011228 BDM

Pyromaniak
15th February, 2018, 05:03 PM
0281011228 BDM


i still have dtc 0010 and limp, its possible make dtc and limp mode off? on this file?

daynight
16th February, 2018, 09:48 AM
P0010 - Camshaft sensor circuit?

Pyromaniak
16th February, 2018, 10:24 AM
P0010 - Camshaft sensor circuit?

yes, if iveco have same codes like eobd... Camshaft senzor new, voltage to senzor 5v, osciloscope signal controled. Timing chain controled. vires with signal measured by the way to mpc...

I thing have bad data for ecu, or something. Now i try reflow mpc. but nothing, every same.

Please can everyone off limp and this dtc? 0010 - my delphi say unknown code

daynight
16th February, 2018, 02:06 PM
Check the timing belt for stretched. I had same issue. After replace belt problem solved :)

Pyromaniak
16th February, 2018, 03:10 PM
i have chain, its one year old, maybe 10000-15000 km. Car is in weekend use only... i have looked on timing, i borow special tool for aretation. everything is ok.

bobolin4o
16th February, 2018, 04:07 PM
Be my guest!

Pyromaniak
16th February, 2018, 09:11 PM
hi bobolino, thank you wery much. Stil have same dtc, i have immo off maybe is problem in eeprom? i need working file for 0281011228 ecu motor f1c 3.0 with no egr (car have not from fabric) no variable turbo and immo off if posible.

Thank in advance

edit. now i try with KTS (borowed from friend) and have code $10 and with delphi 0010, but no P0010

johak
16th February, 2018, 11:18 PM
if you want to try this solution dtc 0010 off

Pyromaniak
16th February, 2018, 11:23 PM
thank you, i try it and report

bobolin4o
17th February, 2018, 07:35 AM
hi bobolino, thank you wery much. Stil have same dtc, i have immo off maybe is problem in eeprom? i need working file for 0281011228 ecu motor f1c 3.0 with no egr (car have not from fabric) no variable turbo and immo off if posible.

Thank in advance

edit. now i try with KTS (borowed from friend) and have code $10 and with delphi 0010, but no P0010

Yes, i know, that this is error code #10, there is not OBD codes in this file... and for sure i've delete it.
Unfortunately, ESI don't have description for this code. What the KTS said about this code? Or is unknown?
How did you flash my file? I hope BDM, not OBD...
And second... have you limp mode again?
Regards!

Pyromaniak
17th February, 2018, 09:43 AM
Hi

What the KTS said about this code? kts say engine driving (řízení motoru) i think my immo off eeprom is very diferent, its possible my problem?

yes, i write by bdm.

i think limp is on, i not drive, but motor can not go over 3200 rpm on neutral. (its possible this car have launch control like mercedes vito? on place no go over3000.)

thank you

bobolin4o
17th February, 2018, 11:12 AM
Test this file... about limp...
The pass is same.

Pyromaniak
17th February, 2018, 02:39 PM
if you want to try this solution dtc 0010 off

sorry for delay, same dtc and limp. rev´s not go over 3200.

Pyromaniak
17th February, 2018, 02:50 PM
Test this file... about limp...
The pass is same.

Thank you bobolino, car now run to 4000 rpm but dtc is same.

i think $10 is bad eeprom. i post it here 0010 is eeprom immo off, and the next one is for this flash from Eight (post 2)

i think maybe help me else immo solution--> have someone else immo off solution for this ecu?

MANY THANKS FRIENDS

Pyromaniak
18th February, 2018, 07:16 PM
Friends, car now run very good. Thanks to MASTER Bobolino :) But mil lamp blinking(i think because immo is off), how it turn off?
If i read immo box , its possible make pair of immo box vith ecu eeprom?

Have someone pair immo dump and ecu eeprom?

Thanks in advance