View Full Version : Passat new ESCL adaption
dunkler
22nd February, 2018, 07:05 PM
I
I have Passat B6 which I've replaced ESCL with a brand new one and now I try o adapt using VCDS
If I go to 25-Immobilizer I get error 22: Conditions not correct
If I go to 46-Confort I get error 35: Invalid key
Pin Is 23729 from CCM
Engine ecu accept this Pin
What could be wrong?
Thank you
rafal
22nd February, 2018, 07:18 PM
Make sure a battery charger is connected so the voltage is maintained.
[25-Immobilizer]
[Adaption - 10]
Leave channel at "00"
[Read]
[Save]
[Done, Go Back]
[Security Access-16]
Enter the vehicle PIN in a 5 digit format.
[Do it!]
[Adaption - 10]
Read Channel 051.
The Stored Value will be 32000. Enter the PIN in the New Value box.
[Test]
Wait | N/A | N/A | N/A Will be displayed. Wait until the ID numbers are transferred into the first 2 boxes. If you aren't sure, be patient and wait at least 30 seconds!
[Save] (Note: if Save is not available and the data in the last step has transferred continue by exiting)
[Done, Go Back]
Check fault codes in all installed control modules and clear them as needed
dunkler
22nd February, 2018, 08:17 PM
Thanks
I've followed the exact same procedures but when accessing Security Access-16 and entering the PIN vcds say "Error 22: Conditions not correct"
I don't have waiting times
I should leave ignition on longer?
rafal
22nd February, 2018, 08:22 PM
is it replacement part number correct?
dunkler
22nd February, 2018, 08:36 PM
Yes, I guess either the pin is wrong or the modules is corrupt or have been changed in the past.
Basically won't accept the pin to enable channel 51
rafal
22nd February, 2018, 08:42 PM
first make sure you do not have any Lock out time at measuring block value 024, if you do just wait till it goes off , switch ignition off/On then go to adaptation CH50.
Group 003: Lock Times && System Status
??? Lock Time Immobilizer
0.0 Lock Time Engine
0.0 Lock Time Transponder
0.0 Immobilizer (LED) Status
check your lock time or post autoscan
dunkler
24th February, 2018, 01:08 PM
All fields are 0.0 , no waiting time.
Could be the PIN wrong? Thank you
brend
24th February, 2018, 02:31 PM
All fields are 0.0 , no waiting time.
Could be the PIN wrong? Thank you
Pin look like correct.
Send all trable code what car have.
dunkler
24th February, 2018, 04:41 PM
here
https://pastebin.com/Dt2CQhL7
brend
24th February, 2018, 04:45 PM
here
https://pastebin.com/Dt2CQhL7
Its fault code after ..clear all faults code.. .?
dunkler
24th February, 2018, 04:54 PM
here is after erased dtcs
https://pastebin.com/xWbifCNw
brend
24th February, 2018, 05:03 PM
here is after erased dtcs
https://pastebin.com/xWbifCNw
If look at fault code ,ecu have same power trable not immo/escl/key....... .
..........................ECU..................... ............
005633 - Relay for Supply Voltage Terminal 30 (J317)
P1601 - 000 - Implausible Signal
yugo45
24th February, 2018, 09:30 PM
Turn Hazards On, and switch light switch off/on for about 10 min to keep CCM alive.
After that Try procedure in post #2 but with out security access with PIn, , go straight to adaptation Ch51 and see what will happen.
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.