Tl866cs programmer

[mister opel]

I have tl866cs programmer bought for me. I am struggling to write a am29f010 and am29f010b flash chip from a dupec ecu. I can't erase the chip. I tried many chips but same problem. I unprotect but its not working. If someone can tell me where I'm going wrong please help. I must erase before I can write. Thanx.
I can read it only but not erasehttps://uploads.tapatalk-cdn.com/20180304/f81e3f7acf9a3211e5647a2d77cda24c.jpghttps://uploads.tapatalk-cdn.com/20180304/89b5c3238082239c37f9095afa69c691.jpghttps://uploads.tapatalk-cdn.com/20180304/ac9c5047ab5e98e45d3cb6145052744b.jpg

Sent from my WAS-LX1 using Tapatalk

[pocinas]

If you desolder this memorys from ECU, you can just READ tehn,,

For Programming you should buy new Memory and then flash it.

[DR Race]

Sorry my bad , this chip can be erased and new programmed, no need for new one !

Trimis de pe al meu SM-G930F folosind Tapatalk

[exe123]

29f010 is flash based and not OTP. Try a different programmer.

[heteromies]

I have tl866cs programmer bought for me. I am struggling to write a am29f010 and am29f010b flash chip from a dupec ecu. I can't erase the chip. I tried many chips but same problem. I unprotect but its not working. If someone can tell me where I'm going wrong please help. I must erase before I can write. Thanx.


Sent from my WAS-LX1 using Tapatalk

NO DEVICE found? So is your programmer setup ok or is it clone...?

[mister opel]

NO DEVICE found? So is your programmer setup ok or is it clone...?I suppose it is a clone as it's bought on wish for relatively cheap. But it works nice on all other chips. All drivers installed and software working with hardware nice. Only can't erase chip above

Sent from my WAS-LX1 using Tapatalk

[gumacz100]

511298
Im write like this.

[mister opel]

511298
Im write like this.And how do u erase? I can't erase. That's my problem

Sent from my WAS-LX1 using Tapatalk

[raceshadow]

I can see 29C010B on the photo.

[mister opel]

I can see 29C010B on the photo.It is a AM29F010B

Sent from my WAS-LX1 using Tapatalk

[mister opel]

Still nothing guys?

Sent from my WAS-LX1 using Tapatalk

[gljuk]

Did you try to resolder the adapter?

[ussr100]

Fill the "FF" block and press the programming chip.
The Erase function may not be supported.

511937

[mister opel]

Fill the "FF" block and press the programming chip.
The Erase function may not be supported.

511937Adapter seems fine. I suppose the erase function is not supported. However the reviews on this programmer was real good. It's a real pity.
I'll try to get hold of the manufacturer for their info.
If anyone maybe knows how to erase this chip with minipro pls do let me know at some point.
Tnx forum

Sent from my WAS-LX1 using Tapatalk

[mister opel]

Adapter seems fine. I suppose the erase function is not supported. However the reviews on this programmer was real good. It's a real pity.
I'll try to get hold of the manufacturer for their info.
If anyone maybe knows how to erase this chip with minipro pls do let me know at some point.
Tnx forum

Sent from my WAS-LX1 using TapatalkWhat do you mean with fill the FF block? You want me to try and program the chip with FF data all the way?

Sent from my WAS-LX1 using Tapatalk

[shafo]

I use this exact programmer to do dupec ecus and ive always had success !
when the "check id" box is ticked does it not read?

[mister opel]

I use this exact programmer to do dupec ecus and ive always had success !
when the "check id" box is ticked does it not read?Some chips read but most don't. I have to unselected the check id then I can read. But I can't erase. It just say erase successfull but chip still fully written.

Sent from my WAS-LX1 using Tapatalk

[mister opel]

Update.

AM29c010 chip must be played with untill chip I'd reads correct. When the chip is removed it reads as all sectors unprotected. In my effort to learn this chip I have protected some of the sectors by mistake. tlc866 can not unprotect this flash chip sectors, but it can protect sectors. Once you click the protect some of the sectors button you are basically stuck and can not unprotect the protected sectors thus being stuck. Then writing or erase can not proceed.

By default all these sectors read as unprotected.
So unless you protect sectors you will be ok to erase and write.
So now I'm stuck with 21 protected chips.waiting on new ordered ones-now it's 3 months allready. Patiently.

Also I have have found some of my chips have changed I'd after messing with them to much.
Off to the bin with them.

Sent from my WAS-LX1 using Tapatalk

[familiozo]

I use the same programmer for am29... read and write without problem,sometimes plcc32 socket adapter make problem,If you have buy am29f010 from china 3 from 5 working.

[pocinas]

I'm not sure for that but what i know chip 29f010 is just one time programmable chip... so only way is read and buy new empty chip and then programmable new chip.


And to let know very important things..... every time after desolder chip from pcd is cleaning chip pins and socket pins using isopropyl alcohol... or inspection pins/ connection between chip/socket under microscope

[bersch8688]

Yes fill your dump complete with FF and click Write!

[mister opel]

No you can rewrite lot of times my friend

Sent from my EML-L29 using Tapatalk

[familiozo]

Hi i have the same programmer and work without problem with am29f010,may be plcc32 socket no contact good with chip for me this is reason for not erasing the chip.

[attila1975]

Hello amiko I have the same programmer I had the same problem if you want to fix bought new brands of AMD brand ... Only so I wrote again ... Then this particular programmer you have to specify the type of mar a processor if you take one like it reads it but he does not write it gives you an error ... Ok bye