PDA

View Full Version : PSA Motronic ME7.4.4 Idle speed



xdamdamx
7th March, 2018, 11:57 AM
Hello friends!

I'm trying to find Idle speed maps in a Citroen C2 VTS Rally car with sport camshafts, because it stalls below 1500RPM. Could you please help me with this ?
There's no DAMOS/SuperMapPack easy to find. Of course not looking for a free solution :)

ORI read in attachement.

thanks for help!

bobolin4o
7th March, 2018, 12:18 PM
What you want actually?
Idle speed 1500 rpm?

xdamdamx
7th March, 2018, 12:33 PM
Yes, idle speed 1500 will be ideal :)

bobolin4o
7th March, 2018, 12:46 PM
Are you sure, that the file is ok?
Because when i open it in WinOls, there is wrong checksums...

morgano
7th March, 2018, 12:53 PM
Are you sure, that the file is ok?
Because when i open it in WinOls, there is wrong checksums...

Guess most checksum errors are because is partial read.

bobolin4o
7th March, 2018, 12:54 PM
Is full read - 512k, that's why i asking...

Any way... here is your requested file.
When the engine is cold, the idle will be 2000 rpm.
When the engine get hotter, the idle will down to 1600 rpm.

morgano
7th March, 2018, 01:22 PM
The file size is 512Kb but the partial is embedded inside rounded with tons of FF's ;)

bobolin4o
7th March, 2018, 01:27 PM
So will be some drama with checksum, or not?

kamandulillas
7th March, 2018, 10:56 PM
bobolin4o, You can check my file?
i same car for competition.
I previously paid for a personalized chiptuner reprogramming and I do not feel any increase power.
the car is decat
manifold exhaust GR.a Daluz 4-2-1
complete exhaust GR.A
Cams newman ph3.
AFR installation meter
Fuel 98 Octane.
I feel rpm.max increased. around 7500 + -
and rpm idle increased around 1600 + -
pass PM.

thanks!

xdamdamx
8th March, 2018, 12:18 AM
Thanks for your effort bobolin4o , it still doesn't hold idle - when i touch accelerator it holds about 1600-2000 RPM, but when i don't press - it stalls immediately.
as i remember from some ME7 VAG there's also a Torque Reserve at idle map, which should be touched, but i'm blind without a DAMOS :/
Do you have any other ideas ? Anyway, thanks for what you made for now :)

patrickmotors
8th March, 2018, 12:51 AM
I have the same car, do you want to raise the minimum at 1500 rpm?

bobolin4o
8th March, 2018, 09:10 AM
as i remember from some ME7 VAG there's also a Torque Reserve at idle map, which should be touched, but i'm blind without a DAMOS :/
Do you have any other ideas ?

Test it...

Vasily.U
8th March, 2018, 09:30 AM
I'm not sure but try this

xdamdamx
8th March, 2018, 02:12 PM
Thanks, I'll test it in the evening today!

bobolin4o
8th March, 2018, 03:39 PM
I'm not sure but try this

It is an incomplete version of my first file.
If the engine was with original cams... it will be fine, except the value at 18AC8.

xdamdamx
9th March, 2018, 08:58 PM
Thank you friends for alle the interest :) bobolin4o, your v2 file in combination with kamandulillas file allowed me to adjust it finally :) The main problem was that the cams are nearly 290*, and stable IDLE is at about 2000RPM.
The second problem is that the injectors are bigger (from 2.0 16V) and not yet calibrated. I'm looking for KRKTE in this file - and I suspect it to be at address $1956B - could you please take a look ? :)

(http://www.digital-kaos.co.uk/forums/member.php/83140-kamandulillas)

bobolin4o
10th March, 2018, 08:09 AM
I'm looking for KRKTE in this file - and I suspect it to be at address $1956B - could you please take a look ? :) (http://www.digital-kaos.co.uk/forums/member.php/83140-kamandulillas)

It is at 19569, with factor 0,002133 and precision 4.
Regards!

bobolin4o
16th March, 2018, 07:04 AM
So... any news about this project?

bobolin4o
25th August, 2018, 04:23 PM
For fratelo...
Regards!

galiza
21st June, 2019, 09:58 AM
Hello, anyone know where are the idle maps for this ecu?

Or where to find the correct damos for ME7.4.4?

I was looking the ME7.5 for PSA V6 but doesn´t fit.

Rupucs
3rd February, 2020, 11:05 PM
Hi, i just made a similar car configurations (newman ph3, decat) and my car just wont idle at all, it just starting to somehow normall working at 1500rpm. Did your cart worked at idle normaly?

Leonsri
10th August, 2020, 10:50 PM
Ffffffffffffff

nikolovs
20th October, 2020, 06:01 PM
Hello all,
I need full and engineering damos for Bosch PSA ME7.4.4 . I have made migration from my ECU Sagem S 2000 to Bosch PSA ME7.4.4, the engine is TU3JP. For that I want full damos to change the fuel in idle speed , VE table , Lambda , Throttle and .. I have found manualy the 2 Spak advance maps, VE table and pedal maps , but another I dont have . I will pay . I have upload the original firmware

joserejo
21st January, 2021, 06:01 PM
LA TENGO UN PROBLEMA SIMILAR CON LAS CAMS PH3. ¿PUEDES PROPORCIONARME EL MAPA? GRACIAS

joserejo
21st January, 2021, 06:13 PM
[QUOTE = bobolin4o; 3356009] Para fratelo ...
¡Saludos! [/ QUOTE]
HELLO I HAVE A SIMILAR PROBLEM WITH THE PH3 CAMS. CAN YOU PROVIDE ME THE MAP? THANKS

PatrickRMA
11th January, 2022, 03:03 PM
Hey guys, same issue. cams chang860022ed and need to idle up. Help?? cant find the adres...

PatrickRMA
11th January, 2022, 03:17 PM
860029
860031

for Nikolovs, ori Damos

Leonsri
29th June, 2022, 01:39 AM
It is at 19569, with factor 0,002133 and precision 4.
Regards!

Hi Bobolin4o which Dam/A2L are you using?

Jesper74
25th May, 2023, 10:15 AM
Peugeot_206_1998_1.6_16v_110_hp
can u do also plsssssssssss

Adrian ADT
25th May, 2023, 08:09 PM
Hello,
an anyone help with idle speed after putting the rollers on the border of 1600-1700 rpm is best :) file on mega: https://mega.nz/file/Xp5QCC7Z#ab7h6cEHZkFTiHVT1_Z4Bi4KsBclzBi4Zd6MjkBrx 3U

Leonsri
26th May, 2023, 08:55 AM
[QUOTE=Adrian ADT;4552654]Hello,an anyone help with idle speed after putting the rollers on the border of 1600-1700 rpm is best file on mega: https://mega.nz/file/Xp5QCC7Z#ab7h6cEHZkFTiHVT1_Z4Bi4KsBclzBi4Zd6MjkBrx 3U[/QUOTE


Your software in the link is corrupt. No data tables in it. File size only 32kb. Kess ME745 is 128kb ME744 512kb. Ktag ME745 832kb ME744 512kb.

Leonsri
26th May, 2023, 08:56 AM
Peugeot_206_1998_1.6_16v_110_hp
can u do also plsssssssssss

Yes send your read file to xxxxxxxxxxxx

Adrian ADT
27th May, 2023, 08:17 PM
[QUOTE=Adrian ADT;4552654]Hello,an anyone help with idle speed after putting the rollers on the border of 1600-1700 rpm is best file on mega: https://mega.nz/file/Xp5QCC7Z#ab7h6cEHZkFTiHVT1_Z4Bi4KsBclzBi4Zd6MjkBrx 3U[/QUOTE


Your software in the link is corrupt. No data tables in it. File size only 32kb. Kess ME745 is 128kb ME744 512kb. Ktag ME745 832kb ME744 512kb.

This is a CMD file, and zip file:) read file : https://mega.nz/file/2gJBUQqQ#XR3U3iqVkizzp2TSDqZ6KDcUsFzzD0usBmhL-ZvJf5w

Leonsri
29th May, 2023, 04:32 AM
Idle set to 1500 Rpm.
Pass In PM.

Adrian ADT
29th May, 2023, 09:49 AM
No pass on PM