PDA

View Full Version : Galletto killed DCM 3.7 !!!!!!



honingkoning
26th March, 2018, 01:30 PM
Guys Today my Gall killed a dcm3.7 (1.2tdi)
Is there a way to get this running again?
I can diag ecu error p1570 active.

I cant write ori file back due to active immo i quess.

Could Some one his experience, Did someone had the same situation, as ussual No reaction from FG.

Wbr Adam.

SpecZ
26th March, 2018, 01:32 PM
Guys Today my Gall killed a dcm3.7 (1.2tdi)
Is there a way to get this running again?
I can diag ecu error p1570 active.

I cant write ori file back due to active immo i quess.

Could Some one his experience, Did someone had the same situation, as ussual No reaction from FG.

Wbr Adam.

Most likely a CMD will save the day.

Any acess to one?

BR.

Michael

honingkoning
26th March, 2018, 01:33 PM
Yes have acces to cmd,
How to restore, with a FRF?

Wbr

SpecZ
26th March, 2018, 01:45 PM
Yes have acces to cmd,
How to restore, with a FRF?

Wbr

Yes since CMD does not make a VR read the FRF should do it.

Post original file to gave a look, perhaps i have that FRF you need.

voltechcar
26th March, 2018, 07:38 PM
use AVDI or VCP to flashing car file frf and he start. I do several time this ecu Kess and never have problem

honingkoning
26th March, 2018, 08:05 PM
use AVDI or VCP to flashing car file frf and he start. I do several time this ecu Kess and never have problem

I Did for sure 20 cars with Gall But now 1st time problems.

But i must say that Gall is a bad option for new cars.
And the attitude of the company is extreme bad.

I Try with a FRF file and see What Will happen, i found a vcp cn Lets see if that works otherwise i try with cmd.

I keep you Up to date.

Wbr

SpecZ
26th March, 2018, 08:44 PM
If you need the corresponding FRF file here it is.

BR.

Michael

looly
26th March, 2018, 08:53 PM
use AVDI or VCP to flashing car file frf and he start. I do several time this ecu Kess and never have problem

OP - sorry to here that fg killed this ecu.


Voltechcar - which kess have you used successfully on this ecu pls? Clone or org? Thanks

voltechcar
26th March, 2018, 08:57 PM
only genuine tools, i not use clone

icezero2010
26th March, 2018, 09:03 PM
my cmd killed also one .

best way is 12-13v power and warning light on than the can bus go not sleep

honingkoning
26th March, 2018, 09:05 PM
my cmd killed also one .

best way is 12-13v power and warning light on than the can bus go not sleep

Thanks for that, But Did tor tool finished writting?
Gall went to 100% all as ussual.

You where able to restore ecu? Or replaced it?

Wbr Adam.

icezero2010
26th March, 2018, 09:09 PM
Thanks for that, But Did tor tool finished writting?
Gall went to 100% all as ussual.

You where able to restore ecu? Or replaced it?

Wbr Adam.

i restore it . yes write all good 100% after that car not start

honingkoning
26th March, 2018, 09:09 PM
i restore it . yes write all good 100% after that car not start

Restore with FRF?

LaraVAG
26th March, 2018, 09:19 PM
yes, galletto support its very very bad.

icezero2010
26th March, 2018, 09:32 PM
Restore with FRF?

yes but with odis

dimitar
27th March, 2018, 12:39 AM
Juzt use odis with any passthru or vas interfacce and make update.....

honingkoning
28th March, 2018, 11:32 AM
Cant write it with cmd (frf file) Guys, i think due to immo issue.

Any idea?

Wbr

sdtsedat
28th March, 2018, 01:09 PM
You cannot try with VCP or ODIS?

honingkoning
28th March, 2018, 05:26 PM
You cannot try with VCP or ODIS?

I Try vcp But Will this bypass the immo issue?
Any experience Guys.

Wbr

voltechcar
28th March, 2018, 05:36 PM
of course ecu you have in car? if galetto erase immo block you not do frf because ecu is locked and any device not flashing frf file this ecu. You must programing again immo

honingkoning
28th March, 2018, 05:58 PM
of course ecu you have in car? if galetto erase immo block you not do frf because ecu is locked and any device not flashing frf file this ecu. You must programing again immo

How to program immo? What tool can do it.

Wbr