PDA

View Full Version : Fail with kess Denso ecu



sdtsedat
2nd April, 2018, 06:26 PM
Someone have do this ecu with kess v2 cline red pcb 5.017?
I do this, read no problem and if write it erase, write and then fail error.

Car is Opel zafira 1.7cdti 110hp 2008 witj denso ecu.
I calc checksum, nothing.

Recovery work and car start, but i am unstatisfied with this.

I have kess geniune but need to activate.
Anyone opinions?

https://uploads.tapatalk-cdn.com/20180402/44968a084bc26da04c1c639dc36d8cc6.jpghttps://uploads.tapatalk-cdn.com/20180402/2b066eb711c2be925ffa92733bd1508c.jpg

Verstuurd vanaf mijn SM-G955F met Tapatalk

maajkii
2nd April, 2018, 07:05 PM
4.036 R/W no problem.

mancioks
3rd April, 2018, 06:38 AM
Astra H same ecu, same year - read/write ok with 5.017

cawadany
5th April, 2018, 02:30 PM
4.036 R/W no problem.

4.036 does not support Opel Denso

maajkii
5th April, 2018, 03:31 PM
4.036 does not support Opel Denso

im shure reworked support ;)

cawadany
5th April, 2018, 03:56 PM
im shure reworked support ;)

It's not fw 4.036. Opel Denso is supported from 2.11, and 4.036 uses 2.08

maajkii
5th April, 2018, 04:10 PM
i use 2.11 from 2years, done few opel denso without problem.

cawadany
5th April, 2018, 04:54 PM
i use 2.11 from 2years, done few opel denso without problem.

With firmware 4.036 it's impossible.

dtip
5th April, 2018, 05:06 PM
i use 2.11 from 2years, done few opel denso without problem.

You can use any higher software version than 2.08 (although no point) with FIRMWARE 4.036 but you will have that options grayed. And "reworking" means that there some components are replaced with more quality ones (capacitors, murata filters etc...) and does not have any effect in SW/FW. That screenshot is from 5.017 fw

morgano
5th April, 2018, 05:17 PM
You can use any higher software version than 2.08 (although no point) with FIRMWARE 4.036 but you will have that options grayed. And "reworking" means that there some components are replaced with more quality ones (capacitors, murata filters etc...) and does not have any effect in SW/FW. That screenshot is from 5.017 fw

If maajkii say he uses ksuit 2.11 for sure his hardware is not 5.017 fw based. 5.017 cannot run on 2.11, need special 2.2x version of ksuite.

norman1967
31st July, 2018, 08:55 PM
Hello lads.

What is final answer? I have 2009 Astra h denso to read write tommrow I have genuine kess with eu 5.017 nxp. Using 2.47....

We have good results or not?

sdtsedat
31st July, 2018, 09:15 PM
Don't do it... you will receive error...

Verstuurd vanaf mijn SM-G955F met Tapatalk

mancioks
1st August, 2018, 12:40 PM
Chinese v2.23 read/write ok, but genuine will not? I dont believe :)

morfej
1st August, 2018, 12:47 PM
I agree with mancioks, I done it with 2.23 and fw 5.017

norman1967
1st August, 2018, 01:01 PM
I just did it with smok. Everything worked well

carmageddon
1st August, 2018, 01:44 PM
Chinese v2.23 read/write ok, but genuine will not? I dont believe :)

read better what norman1967 wrote : I have genuine kess with eu 5.017 nxp. Using 2.47....

genuine kess with fw 5.017????? he have a clone!

juse
1st August, 2018, 04:17 PM
read better what norman1967 wrote : I have genuine kess with eu 5.017 nxp. Using 2.47....

genuine kess with fw 5.017????? he have a clone!

He might have genuine kess slave or master that has been "unlocked" by chainching the nxp and sd card

norman1967
1st August, 2018, 04:21 PM
Yes I have genuine hardware was a slave I swapped nxp and sd card for eu. However I used smok on the ecu and it worked perfect

carmageddon
1st August, 2018, 04:35 PM
anyway : is a clone, not genuine!

a17h641a
19th February, 2020, 08:09 PM
hello everyone, can someone help me. You KTag and Kess boxes with all accessories, but the software does not run under windows 7, what can or do I have to do that I get the boxes to run. Thank you

damjantuze
20th February, 2020, 02:12 AM
I have done many denso with kess clone 5.0 with 2.23 no problem at all