TMS374 Decoder tool

[magdex]

Hi all
I need instruction for this Tool ! How to use it !

Regards

[MOBILTRONIC]

Like Tiny sweeper

[magdex]

ok Thx
I test it

[MOBILTRONIC]

You must first,make it,small interfaces and the end manual is the same like tiny sweeper.Look the pictures and shematic connect 28f and 27c.Is the same that.Good luck!

[jokersat]

you wan share this info and put as rar files

thanks

@+

[kasim_izmir]

you wan share this info and put as rar files

thanks

@+
Hi to all friends
Here is all tms374 decoder files

[jogi]

And here the original source of the Tiny sweeper project:

h..p://tmw.netlook.pl/download/Tiny%20Sweeper%200.3.rar

regards

[Akhenaton]

thx bro very nice

[magdex]

Thx all i go yo made it

[magdex]

It's Working OK !

Thx to kasim_izmir

Regards

[mancinofranco]

This TMS374 decoding was for sale in Italy at 80 euro without assistance fron Sicily

[ahadi]

is this soft could decode sagem sl96-9 ecu with 29c512.

[ahadi]

is this soft could decode sagem sl96-9 ecu with 29c512.

[addgsm]

good stuff
thanks

[cartech]

is this interface and decoder software worked well??????????

any body have tested it?
I need to check it on renault cars.
thanks

[nakamichi]

Thanks for information

[busaman]

it does not show the ecu wiring for sagem sl96.

[terraporn2k]

Thanks for all the useful info in this thread :)

[ggpanos]

Hi to all friends
Here is all tms374 decoder files

Hi all,

I have test this long ago. At first, when I was using a desktop P4 3.0GHz with on-board serial port (COM) the tms374 decoder did not work. Later, I tried the tms374 decoder on a USB-to-Serial adapter and it worked 100%. After that, I check the decoder output with an oscilloscope and in my case, the COM port form my desktop seems not to be fast enough.

I hope this may help some of you :ciao:

[thunder2]

thanks good software

[stevexwwe]

thanks ill give it a go

[gejzaslapka]

Hello,
has anyone tested this sweeper on SAGEM SL96-3 from peugeot 306 1.4 engine code KFX


WBR
GS

[oscar2000cz]

thank you very much

[radiodecoder23]

Hello ,
This tool is very good sweeper...

http://www.therealdigitalsolutions.com

[umut66]

exe file does not work but thanks for sharing

[mexanico1971]

HI ! im bulding this interface but i have some problem to interpreted the schematic! to remove a immo from a 1AP40 !
just need to conect one wire to the 28f512 ? and the tms 374 !
thas anyone know how do this ?!

[sivolcf]

Hi,

I'm newbie in this forum, need help.
Is it hard to reset an Sagem Safir2 35 pin renault ECU with CAN CLIP ? TMS374 Chip in ECU

[defowach]

Hi all,

I have test this long ago. At first, when I was using a desktop P4 3.0GHz with on-board serial port (COM) the tms374 decoder did not work. Later, I tried the tms374 decoder on a USB-to-Serial adapter and it worked 100%. After that, I check the decoder output with an oscilloscope and in my case, the COM port form my desktop seems not to be fast enough.

I hope this may help some of you :ciao:
Would like to know on which reading to switch the oscilloscope -volts or frequency -& which kind of reading is it supposed to output.

[zebulon478]

Hi all
I need instruction for this Tool ! How to use it !

Regards

Hi everybody, I'm in the same case, ready to share and I need instruction for this tool.
I read the post and find it interesting.
I investigate how I can perform well with...

Best regards:)

[zebulon478]

HI ! im bulding this interface but i have some problem to interpreted the schematic! to remove a im*o from a 1AP40 !
just need to conect one wire to the 28f512 ? and the tms 374 !
thas anyone know how do this ?!

Hi mexicano1971,

I've some documentations, may be I can help?
Do you need the schematic of 1AP40 MCU pins?
For now, I cannot see your attach files, and know what you need exactly sorry...

Best regards

[deneo]

i built the interface and messed about with it for 2 weeks and it did not work

[butcha33]

i built the interface and messed about with it for 2 weeks and it did not work

Just pick one up from tek-tronics (http://www.tek-tronics.co.uk/product_info.php?cPath=33&products_id=118)

[jpay2]

Hello, with Max232 pin plug to wait long it is?

[AMON]

anyone had success with max232 interface


thanks

[ferbenja]

thank you

ferbenja

[tigar]

thanks to you

[i_shot_the_sheriff]

I bought the one from Italy and it's not working!!
Ive tried everything :/

[butcha33]

I bought the one from Italy and it's not working!!
Ive tried everything :/

hello, where did you buy it from? have you used the one from Tek Tronics UK - Advanced tools for car electronic and immobilizers repair (http://www.tek-tronics.co.uk) ??

what ecu do you have a problem with and how are you wiring up?

thank you

[zeca]

hi i have some problem to that interpreted the schematic components are J1 and J2 excuse my ignorance
thanks

[zeca]

hi
can you help me about schematic J1 and J2 what is this components
Thanks

[racin-snake]

j1 and j2 are these

5 Pcs PCB Mount 2 Pole Terminal Block Connector Grn 25A | eBay UK (http://cgi.ebay.co.uk/5-Pcs-PCB-Mount-2-Pole-Terminal-Block-Connector-Grn-25A-/180669451690?pt=UK_BOI_Electrical_Components_Suppl ies_ET&hash=item2a10bd0daa)

[Behkli]

Hi all
thanks magdex

[alclot]

Hi mates,
I got this tool and I did a few units but now I have a problem becuase I just power it up and ld is blinking all the time without push button. Can anyone help me why happend that please?
thanks.