View Full Version : BMW 328 MS42 IMMO OFF
makura
13th April, 2018, 09:55 AM
Hallo
I need help to immo off bmw e46 328i using MS42 ecu,i need a tried and tested solution,this car is very far from here.
I have attached ecu dump from 29f400.
Regards
andrelis398
13th April, 2018, 10:09 AM
I think only emulator.
andrelis398
13th April, 2018, 10:11 AM
try
http://www.digital-kaos.co.uk/forums/showthread.php/552226-immo-off-free-for-all
makura
13th April, 2018, 10:12 AM
unfortunatly the last emulator i have keeps giving me an error "no echo from k line" when i try to program ISN into it.
WinWoj
13th April, 2018, 10:46 AM
in this system is transponder coil problem, i used old key which sometimes not run and immo fail, so i dismounting coil, improved pins, take out transponder from key and glued to coil, coil glued under steering column and always engine started. no immo problem again.. You cannot be surprised that k-line blocked because emulator sending his own data. such emulator.. but maybe someone had off solution, when I repaired my case, nobody helped..
makura
13th April, 2018, 10:55 AM
I hear CarLabImmo has a working dump for MS42.
aqua_life
13th April, 2018, 11:17 AM
Hi,
I also have the same problem and want to remove immo from MS42.
You can check my thread here:
http://www.digital-kaos.co.uk/forums/showthread.php/655952-BMW-e46-328i-MS42-Immo-OFF?highlight=ms42
I tested the file OFF on the thread and its not ok.
Thanks for your help
makura
13th April, 2018, 04:16 PM
Does any have dump file from a EWS emulator using atmega 48?
dodge69
13th April, 2018, 05:13 PM
hello, I kind of managed to shoot the solution on ms42 CarLabImmo . but I have everything in the photo and they take up a lot of weight. You may have to rewrite the dump by looking at the pictures. If it's still real, then in 3 days I'll try to attach the photo to my inbox at home
SPIROS2105
13th April, 2018, 05:40 PM
PUT THIS FILE REMOVE EWS AND MAKE BRIDGE TO STARTER
makura
13th April, 2018, 05:42 PM
PUT THIS FILE REMOVE EWS AND MAKE BRIDGE TO STARTER
No attachment m8
SPIROS2105
13th April, 2018, 05:57 PM
PASS IN PM
makura
13th April, 2018, 06:02 PM
Wil test and report tomorrow,thanks
makura
15th April, 2018, 10:31 AM
PASS IN PM
Thanks SPIROS2105,you file worked like a charm:tears_of_joy:
But its now trowing gears hard instead of a smooth shift.
aqua_life
16th April, 2018, 08:53 AM
Hello,
I need to make immo off to this BMW ECU from E46 328i
ECU is MS42
Can someone help me ?
Thanks
SPIROS2105
16th April, 2018, 10:08 AM
take your file
pass in pm
vaglupo
23rd May, 2018, 09:35 AM
Hello
Please help me with this file with Immo off.
E46 328IA
Br mirko
ozzzo
24th May, 2018, 09:54 PM
please pass
omar belguith
26th May, 2018, 01:55 PM
tested ok 100 %
531202
PASS IN PM
ozzzo
28th May, 2018, 07:58 AM
pls pass for5wk9037
thx
ozzzo
28th May, 2018, 08:04 AM
PASS IN PM
psl pass 328_MS_42
THX
SPIROS2105
28th May, 2018, 09:58 AM
i dont remember pass
post your file
pepesound
14th June, 2018, 01:55 PM
Hi friends please help with immo off BMW 328i with DME MS42.Thanks in advance!
pepesound
15th June, 2018, 01:16 PM
No one can help with a solution to this problem
ozzzo
24th September, 2018, 03:53 PM
PUT THIS FILE REMOVE EWS AND MAKE BRIDGE TO STARTER
hello can you help in ews off ms42 7500 255?
meteinam
1st October, 2018, 05:41 PM
PASS IN PM
can you send me pass please
silvarog3r
22nd November, 2018, 09:48 PM
i dont remember pass
post your file
Hi pass thanks
rrrst
22nd November, 2018, 10:28 PM
For MS42 look here:
https://www.ms4x.net/index.php?title=Original_Files#Virginized_01100AD
checka
20th February, 2019, 02:29 AM
Hi! need Immo off for MS42 328i
toni_18674
26th March, 2019, 07:03 AM
Hi can you help me with this DME MS42 IMMO OFF please?
dkmi
14th May, 2019, 07:21 PM
Hi can you help me with this DME MS42 IMMO OFF please?
test to flash with this
bassit
17th June, 2019, 07:57 AM
Hello
I need a tested immo off bmw e46 ecu siemens ms42 5wk9037
bassit
17th June, 2019, 02:38 PM
no solution?
Lambda1
17th June, 2019, 08:56 PM
Soltuion is posted in your other threader, based on your file.
Tested solution.
dkmi
24th June, 2019, 07:02 PM
Hello
I need a tested immo off bmw e46 ecu siemens ms42 5wk9037
flash.
ews is off, Checksum is corrected.
gui325
25th June, 2019, 08:17 AM
Hello
I have a same problem on my Ms42 328i, I just send this file in DME for Immo off ?
Thanks
gui325
25th June, 2019, 02:15 PM
hello
thanks for your file
please pass ?
dkmi
26th June, 2019, 06:43 AM
hello
thanks for your file
please pass ?
There is no pass.
daviee
9th July, 2019, 11:09 AM
Hello!
Can you help me also please remove immo froim this MS42 please?
Thank you.
Best regards
PASS IN PM
dodge69
9th July, 2019, 01:48 PM
hello here keep immo off!
100%
GRUPOMARBE
5th November, 2019, 03:33 AM
PASS IN PM
can you send me pass please
wieslov
15th November, 2019, 02:05 PM
Hello
I need immo off ms42
Lambda1
15th November, 2019, 06:24 PM
here you go.
shanny254
14th December, 2019, 05:56 PM
hi ews delete for this ms42 ecu
thanks
mymyk
23rd March, 2020, 08:13 PM
Hi guys, can u help with immo off?
Lambda1
24th March, 2020, 09:07 AM
For future help be more active!
ziko
30th April, 2020, 01:57 PM
Please off for ms42
ricked
30th April, 2020, 02:36 PM
Please off for ms42
why? its already off.. did you even try it?
ziko
30th April, 2020, 03:48 PM
Not tried,org flash destroyed I found this in my files
You sure is off?
Tnx
Its from this forum file
Yes you're right, I see off string in address 26xxx
tothzsolt
30th April, 2020, 04:49 PM
ziko
Producer: SIEMENS
Hardware: MS42
Software: 0110AD
ECU Prod: 5WK9032
ISN: 12 4F
File data error.
bad dump
ricked
1st May, 2020, 09:51 AM
Not tried,org flash destroyed I found this in my files
You sure is off?
Tnx
Its from this forum file
Yes you're right, I see off string in address 26xxx
so why you ask immo off if you know how it works?
i dont get this....
ziko
4th May, 2020, 03:58 PM
Because I didn't has ms42 for off till now,and asked for tested solution ;)
On bench I get dtc 170 with inpa,control unit selftest internal fault
Lambda1
4th May, 2020, 04:54 PM
Because isnt possible to use every sw-version in every hardware ;)
ziko
4th May, 2020, 05:28 PM
In this case I replaced flash from ori to used ecu and car is ok. Now dtc 170 I have in org defective ecu with flash ic from used ecu (29fxxx swuped)
ricked
5th May, 2020, 08:42 AM
In this case I replaced flash from ori to used ecu and car is ok. Now dtc 170 I have in org defective ecu with flash ic from used ecu (29fxxx swuped)
what P code is dct 170 ?
ziko
5th May, 2020, 11:09 AM
Inpa and bmw scanner not shows p code
seenomore
1st August, 2020, 07:42 AM
Hi, can anyone please help me with immo off for an Siemens MS42 1998 E46 BMW 323i , i have attached org file readin boot mode.
Thank you in advance.
jl01152
21st October, 2020, 10:16 AM
Does anybody have and ews emulator dump from an atmega48 ? I will be getting one in the mail soon and would like to know how to dump the firmware. Want to make an arduino do the same thing.
Suaramusik99
29th July, 2023, 10:30 AM
Hello sir... Please sendiri me password
dadal
6th September, 2024, 04:57 PM
Can someone check my immo off files plaese ?
customer sent a message saying the car doesn’t start when the EWS module is disconnected, but it starts when connected.
However, the file has been modified and isn't original. It's a bit strange that it still works only when the EWS is connected, isn't it?"
Or can you send me the original file for this ECU? I think this software isn't original, maybe it's tuned.
MS42
index4
ca0110c6
5wk9037
BMW E46 2.8
erkor
6th September, 2024, 07:49 PM
Can someone check my immo off files plaese ?
customer sent a message saying the car doesn’t start when the EWS module is disconnected, but it starts when connected.
However, the file has been modified and isn't original. It's a bit strange that it still works only when the EWS is connected, isn't it?"
Or can you send me the original file for this ECU? I think this software isn't original, maybe it's tuned.
MS42
index4
ca0110c6
5wk9037
BMW E46 2.8
.................................
This is not a tun file.
Your files have ews disabled.
It is normal that the car starts when ews is connected. After disconnecting ews, you need to connect two thick pins in the ews cube
dadal
6th September, 2024, 08:57 PM
.................................
This is not a tun file.
Your files have ews disabled.
It is normal that the car starts when ews is connected. After disconnecting ews, you need to connect two thick pins in the ews cube
The customer has disconnected the EWS connector. I'm not sure how, but he bypassed the starter motor. The starter motor runs freely, but he says the car doesn't start. However, when the EWS is connected, the car starts normally again. What you mean by bridging the two thick wires in the EWS connector is likely only meant for the starter motor, right? Otherwise, it wouldn’t crank, correct or it is also for other things ?
In my case, the engine does crank ( EWS disconnected,) but it doesn't start...
erkor
6th September, 2024, 09:39 PM
What you mean by bridging the two thick wires in the EWS connector is likely only meant for the starter motor, right?
YES.
Applies to the starter
dadal
6th September, 2024, 09:59 PM
What you mean by bridging the two thick wires in the EWS connector is likely only meant for the starter motor, right?
YES.
Applies to the starter
Very strange situation... the software has been modified correctly, but without the EWS, the engine won't start ( well crank with bypassed ews) . Maybe I didn't calculate the checksum correctly. Can someone check if it's correct?
And what's also strange is that the software has been modified ,EWS are removed , but the car still starts with the EWS connected and original keys
erkor
6th September, 2024, 10:00 PM
Very strange situation... the software has been modified correctly, but without the EWS, the engine won't start ( well crank with bypassed ews) . Maybe I didn't calculate the checksum correctly. Can someone check if it's correct?
Checksum is OK :)
dadal
6th September, 2024, 10:08 PM
Thanks Erkor mate
have nice night !
erkor
6th September, 2024, 10:11 PM
Thanks Erkor mate
have nice night !
..................
you can try my fie
1044631
Press ONLY thanks for a pass :)
dadal
7th September, 2024, 01:52 AM
thanks + rep are added for you,,
I wil try it
dadal
7th September, 2024, 10:41 AM
..................
you can try my fie
1044631
Press ONLY thanks for a pass :)
Hi Erkor,
I cant download file, do you want to check it please
erkor
7th September, 2024, 11:50 AM
Hi Erkor,
I cant download file, do you want to check it please
.........................
1044717
dadal
8th September, 2024, 12:35 PM
Hi Erkor
cumstomer said, Car didnt start, even with and without EWS module,,
erkor
8th September, 2024, 01:17 PM
..........................
Your file had ews disabled correctly. My file too, but it had a different ISN number because it is from another car.
Maybe that's why it didn't start, because there may be a problem with writing the file to the ECU and no changes are saved except for ews. What program do you use to writing ?
After saving the file to the ECU, read it again and compare with orginal fie whether the changes have been saved.
Try the next file.
I have made many ECUs like this and they all worked fine.
1044801
dadal
8th September, 2024, 06:07 PM
..........................
Your file had ews disabled correctly. My file too, but it had a different ISN number because it is from another car.
Maybe that's why it didn't start, because there may be a problem with writing the file to the ECU and no changes are saved except for ews. What program do you use to writing ?
After saving the file to the ECU, read it again and compare with orginal fie whether the changes have been saved.
Try the next file.
I have made many ECUs like this and they all worked fine.
1044801
You're right, I also mentioned it to the customer yesterday. I can't find any other explanation either. Changes aren't being written to the ECU, which is why the customer will write it first, then read it again and compare. He writes and reads with a Byteshooter. I'm not sure if he's doing it in Bootmode or via OBD, but I'll ask him about that too.
Maybe it would be better for him to use an external programmer to read and write.
I see that in the v3 version, you filled some addresses with FF. Is this for the ISN? Did you remove the ISN?
I see pass is same :calm: need I to correct checksum ?
Thanks a lot for your interest, I'll keep you updated.
erkor
8th September, 2024, 07:01 PM
Checksum is counted.
Fields with FFFF are the ISN number.
You need to use another tools to write the file.
dadal
22nd September, 2024, 10:37 PM
Checksum is counted.
Fields with FFFF are the ISN number.
You need to use another tools to write the file.
Thanks mate,,it is solved,,problem was programmer,, on extern programmer all is OK now
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.