PDA

View Full Version : Help wit MPPS READ error on a 2009 Grande Punto 1.9JTD



brogdan1001
6th July, 2018, 04:00 PM
Hello
i have just bought a MPPS v16 clone and i am trying first to read the original map from the ECU of my FIAT GRANDE PUNTO 1.9 130bhp
i managed to install the software to a XP laptop. great until now
Enter the MPPS software, select the car model and the engine.
First i hit the ECU ID button, it reads the ID ok.
Then i hit READ and it starts reading until 20-80% (did several tries) and then it stops and i get an error.
I attached the pictures of all 3 stages (1-ECU ID, 2-Reading in progress, 3-error)

any help or ideas would be appreciated

lemta
6th July, 2018, 06:54 PM
Hello
i have just bought a MPPS v16 clone and i am trying first to read the original map from the ECU of my FIAT GRANDE PUNTO 1.9 130bhp
i managed to install the software to a XP laptop. great until now
Enter the MPPS software, select the car model and the engine.
First i hit the ECU ID button, it reads the ID ok.
Then i hit READ and it starts reading until 20-80% (did several tries) and then it stops and i get an error.
I attached the pictures of all 3 stages (1-ECU ID, 2-Reading in progress, 3-error)

any help or ideas would be appreciated

Are you using it with Windows XP? If not then you could try using XP and seeing if it makes any difference.

I also bought MPPS v16 from china and it wouldn't work for me with Mk5 Golf. It would ID the ECU but could not read the flash (failed at 0%). In the end I bought MPPS v13 which worked fine. Your issue is probably due to poor hardware from china like mine.

Hope this helps.

brogdan1001
6th July, 2018, 08:37 PM
Thanks for the reply.
I was using windows Xp.
Mine starts to read but never gets to 100%.
Sometimes it stops at 20%, sometimes at 85%. But never gets to 100%

lemta
6th July, 2018, 10:19 PM
Make sure the MPPS cable is pushed into the OBD port properly. Does your car have any issues that might intefere with MPPS from communicating such as wiring issues, aftermarket radio etc? If you have an aftermarket radio try to disconnect it and then try to read ECU.

EDIT: Also try taking out fuses for the cluster. Look in your manual for that.

If after all that you still have issues then it's likely to be an issue with the MPPS cable than anything else IMO.

AVDigitale
6th July, 2018, 10:54 PM
for mpps china clone
the best is mpps v12 or v13 can doing some edc16 cars without problem
i know some edc17 car doing over obd with mpps v13
but about mpps v16 some are very bad some good
interface to you is the problem or first try o install to WP7 32 bit and check if work better

dtip
6th July, 2018, 11:05 PM
It is crap hardware and you can't do anything about that. Even if it reads don't try to write ecu with that piece of sh*t.
At least buy kess or galleto from china....

bersch8688
7th July, 2018, 06:20 AM
Better buy Kess V2 & Ktag
Test with Kess V2 but KTAG BDM safest way ;-)

brogdan1001
10th July, 2018, 07:14 PM
thanks to all of you.
i installed another version of the MPPS software (the one without loader) unde windows 7 64 bit. And everything worked PERFECT.
i managed to read and write the map to the ECU.
works for me!
cheers!

lemta
10th July, 2018, 08:25 PM
thanks to all of you.
i installed another version of the MPPS software (the one without loader) unde windows 7 64 bit. And everything worked PERFECT.
i managed to read and write the map to the ECU.
works for me!
cheers!

Can you post the link to this software as it might help other people?

brogdan1001
10th July, 2018, 08:42 PM
Can you post the link to this software as it might help other people?
yes of course!
i wanted to post it, but i didn't know if it's not against forum rules.
software was tested unde windows 7 64 bit. mpps tool must be connected to the pc, before running the software
No loader needed! just unpack the archive under C:\MPPS, and run the exe.
here is the link:
http://www.mediafire.com/file/ax0x7cfwkjov6w2/MPPS+V16.1.02.rar

brogdan1001
11th July, 2018, 08:56 PM
i can confirm that the mmps v16 clone with the above software is working on:
golf mk5 2.0 TFSI Bosch MED9.1 CAN
grande punto 1.9JTD MJ Bosch EDC16C39 CAN
i remapped this cars with no problems

lemta
11th July, 2018, 09:47 PM
How did you install the windows drivers? Did you just run "64 Bit Driver Installer.exe" or just point windows to the drivers folder?

brogdan1001
11th July, 2018, 09:59 PM
When the driver install pops out Just hit browse and point to c:\MPPS\drivers.
Did not run any exe.