View Full Version : Skoda Octavia 1.8T AGU - K04-001 tuning
nosa
19th July, 2018, 02:32 AM
Hi guys is there anyone who can help me to upgrade my power?
My specs are:
- ECU Bosch M 3.8.3, Audi/VW Part # 06A906018CG
- Engine code: AGU (Drive by cable)
My actual setup is:
- Stage 1 ECU remap, 190 hp/320Nm Immo Off
- 14 lbs flywheel single mass, VR6 clutch
- K04-001 turbo
- Ported exhaust manifold (30% more flow)
- Silicone turbo inlet hose (TIP)
- VR6 MAF housing
- Upgraded DV, Forge DV008
- 3" (76mm) downpipe and catback
- 3" (76mm) Flowmaster Hi flow catalytic converter
- 3" (76mm) Magnaflow resonator and race muffler (direct).
- Short Ram intake with K&N filter
- Front mount intercooler 28" x 7" x 2.5" (711.2 x 177.8 x 63.5 mm)
- 4 pin TFSI coil pack upgrade
- Upgraded Fuel pump flow to 340 lph (@ 43 PSI)
- Injectors installed: stock 205cc @ 4 bar (I have 1 set of Bosch 0 280 150 431, Saab red top injectors to be installed).
- Dogbone poly insert (70A durometer).
- Bilstein sport suspension
- Neuspeed sport springs
Right now the car runs incredible, but I want get the best performance of all my hardware.
Regards.
nosa
12th August, 2018, 02:51 AM
This car was a payment of my friend who own me some money. These pictures are from before, during and after the tune-up of the car.
This is a "low budget" project, so all the components replaced were purchased on sales, specials offers and some cases second hand parts.
What I received.
548708
ECU part number
548709
We started the project.
548710
The old 3 pins ignition coils.
548712
nosa
12th August, 2018, 03:01 AM
Ignition coils Bosch branded, I chosen the used in the Audi R8 (red ones).
548579
eBay provided - 3" Down pipe USD $60, Intercooler USD $60, Intercooler piping kit with clamps and silicone hoses USD $100. Just must research patiently.
548580
3" exhaust system.
548581
Decat downpipe (first installation)
548716
nosa
12th August, 2018, 03:21 AM
Some painting for better looks.
548713
Intercooler piping - attaching the fitting for N75 valve (eBay purchased, doesn't bring this fitting).
548715
Intercooler mounting - easiest than I imagined.
548584
Engine harness and ignition coils upgraded from 3 to 4 pins.
548586
Ready for the first start.
548587
nosa
12th August, 2018, 03:29 AM
Almost done...
548588
Wheels: Niche Verona 17" - Tires 235/45-R17. Daily use setup.
548589
Neuspeed sport springs
548590
Maxxis Victra ZR9 195/50-R15, TRACK TIRES (were a donation).
548591
Skoda Octavia 2 (1Z) steering wheel retrofit.
548599
nosa
12th August, 2018, 03:45 AM
Mesh/Grille modification.
548592
548593
548594
Halogen to projector Headlight upgrade.
548597
LED cluster lights replace.
548598
Apsik
12th August, 2018, 08:20 AM
Hi guys is there anyone who can help me to upgrade my power?
My specs are:
- ECU Bosch M 3.8.3, Audi/VW Part # 06A906018CG
...
Right now the car runs incredible, but I want get the best performance of all my hardware.
Regards.
First off all change the engine management to wideband ME7.5 ... or get yourself wideband AFR meter. Otherwise it's hard to optimaly tune ME3.8
icezero2010
12th August, 2018, 11:07 AM
First off all change the engine management to wideband ME7.5 ... or get yourself wideband AFR meter. Otherwise it's hard to optimaly tune ME3.8
Its not hard :) but he must Unterstand
nosa
12th August, 2018, 10:54 PM
So if I understand, I must use the AFR meter to check the optimal mix when I'm mapping?. (kepping ECU Bosch M 3.8.3)
I'm new in this of ECU tuning/mapping.
raceshadow
13th August, 2018, 07:50 AM
For a beginner, the petrol engine modifications are very difficult. Your old type of ecu must be done through the programmer. So it's better to find someone who has an OLS300 emulator and can do a good remap.
Apsik
13th August, 2018, 10:38 AM
For a beginner, the petrol engine modifications are very difficult. Your old type of ecu must be done through the programmer. So it's better to find someone who has an OLS300 emulator and can do a good remap.
AGU ECU can be flashed with MPPS.
I think finding someone with OLS300 in Panama is very close to "impossible"
nosa
14th August, 2018, 03:50 AM
AGU ECU can be flashed with MPPS.
I think finding someone with OLS300 in Panama is very close to "impossible"
Thanks for the information .
I was researching and found than my specific ECU part number (Bosch M 3.8.3, Audi/VW Part # *06A906018CG- 0 261 206 518 - Bosch M3.8.3 - OBDII not CAN - 1.8L R4/5VT MOTR HS D02 - German made 2002 VW Golf GTI 4 (http://i.viglink.com/?key=0e9889638a4633ff8ab8afe8510032fd&insertId=2c187a544b361a0e&type=H&exp=60%3ACI1C55A%3A11&libId=jkt3lwt401010ekl000DLb9gykgsl&loc=https%3A%2F%2~~~-mkivs.net%2Ftopic%2F11308-urgent-agu-ecu-compatibility-question%2F&v=1&iid=2c187a544b361a0e&out=https%3A%2F%2Fwww.amazon.com%2Fdp%2FB06WLLMDKX&ref=https%3A%2F%2Fwww.google.com%2F&title=%5BMk4%20Golf%5D%20URGENT!!!!%20AGU%20ECU%20 COMPATIBILITY%20QUESTION!!!!%20-%20Engine%2C%20Tuning%20and%20Performance%20-%20uk-mkivs&txt=%3Cspan%3EVW%20%3C%2Fspan%3E%3Cspan%3EGolf%20% 3C%2Fspan%3E%3Cspan%3EGTI%20%3C%2Fspan%3E%3Cspan%3 E4%3C%2Fspan%3E) doors 1.8T AGU engine ) could be tuned through the OBD2 port.
I have VAS 5054a tool, it will work with the MPPS?. Any of you eared or know something about this?.
MrAbsinth
10th November, 2018, 03:00 AM
This one you will have to remap MPPS V13 282962624961
https://www.ebay.com/sch/i.html?_from=R40&_trksid=m570.l1313&_nkw=282962624961&_sacat=0
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.