RCD510 code 95128 + nec

[patifon]

Hello friends, i ask for help to find code for Bosch RCD510 code , i attach dumps 95128 + nec
thanks!

[shooting]

Hello friends, i ask for help to find code for Bosch RCD510 code , i attach dumps 95128 + nec
thanks!

NEC dump problem

wbr

[patifon]

Reading Device Info ...
Vendor code NEC : 10
Extension code : 7F
Function information : 4
Device information 1 : EC
Device information 2 : 7F
Last address of internal flash ROM : 9FFFF ( 655 359 ) { 80A77F7F }
Device name (µPD number) : D70F3356
Security information : 7F
Boot block number : 0
Reset vector address : 0
Bit 0 Chip erase flag : enabled
Bit 1 Block erase flag : enabled
Bit 2 Write flag : enabled
Bit 3 Read flag : enabled
Bit 4 Boot block cluster rewrite flag : enabled
Device Version : 0.00
Firmware Version : 1.11
Firmware Checksum (0 .. 9FFFF) : C285
ok.

[patifon]

Reading Device Firmware ... { Buffor size: 0xA0000 ( 655360 ); Checksum: C285 } ok.

[richiebb]

Hello, the whole buffer is from 0 to 9FFFF that means that the dump must weigh 640kb.

I do not know what reader you use but from what I see, maybe it's protected against reading


Reading Device Info ...
Vendor code NEC : 10
Extension code : 7F
Function information : 4
Device information 1 : EC
Device information 2 : 7F
Last address of internal flash ROM : 9FFFF ( 655 359 ) { 80A77F7F }
Device name (µPD number) : D70F3356
Security information : 7F
Boot block number : 0
Reset vector address : 0
Bit 0 Chip erase flag : enabled
Bit 1 Block erase flag : enabled
Bit 2 Write flag : enabled
Bit 3 Read flag : enabled
Bit 4 Boot block cluster rewrite flag : enabled
Device Version : 0.00
Firmware Version : 1.11
Firmware Checksum (0 .. 9FFFF) : C285
ok.

[patifon]

reader Martech Box II.

[richiebb]

reader Martech Box II.

maybe the MCU has security enabled for reading.............
try with the 2 digit method (http://www.digital-kaos.co.uk/forums/showthread.php/379014-RCD310-510-BLAUPUNKT-BOSCH-Algo-FIRST-2-digits)

[patifon]

What are the first digits of my dump 95128 ?

[Zann]

You need another dump. Read PDF in the link.

[patifon]

This pair is suitable?

[Zann]

This is modified dump from your first post.
Write this dump in the eeprom.
Turn ON the radio, wait 30 seconds and then read again dump from eeprom.
Post that dump here.

[richiebb]

This pair is suitable?

I'm afraid not, do you have another reader to read the NEC?

[patifon]

The remaining attempts 98

[Zann]

First 2 digits 19xx

[richiebb]

The remaining attempts 98

write original dump

[patifon]

The remaining attempts 2

[richiebb]

The remaining attempts 2

yes........... try 1900, 01 and rewrite ori eeprom dump; then 1902,03 and rewrite.... etc

[patifon]

Dump NEC for full code will not help?

[RadioChiP]

Martech dump is maybe special dump format, i do no see now mobile phone...
-But you can try basic Max232 interface read via NEC reader.

[patifon]

Sorry, there was an error,Blaupunkt VW MID EU UP1:hmmmm2:

[patifon]

Martech not work.

Device Information ( EEPROM ) : 95128
Size : 0x4000 (16384) byte
Bus Type : SPI
Bus Mode : 4-Wire Interface.
Bus Speed : 8


Step 1. Reading Device Information ...
Error. Device information read - Failed. ( reading: sn, version, vin ... etc.)

[RadioChiP]

Read another programmer :)
Do you have Upa?Seeprog?

[nokwueze]

pls friends i need diagram for rcd 510 i want to read with orange 5 programmer

[patifon]

Code found 1960, thank you all:dancing:

[richiebb]

pls friends i need diagram for rcd 510 i want to read with orange 5 programmer

Here............

[nokwueze]

Friends i need pinout to this rcd510

[richiebb]

Friends i need pinout to this rcd510

Mate..........look inside PDF!

552591

[nokwueze]

thanks rich am greatful

[nokwueze]

pls i need code for vw delta vwz4z4

[audiopoint]

Friends i need pinout to this rcd510

for skoda you can use standard pin out on power supply connector

[smoggy]

pls i need code for vw delta vwz4z4
try code 1059

[nokwueze]

i have read nec today thanks
5k0 035 190

[smoggy]

i have read nec today thanks
5k0 035 190
try code 1194

[Citrina]

help with code
nec and 95128 read

[shooting]

help with code
nec and 95128 read

Your code is 0554

wbr

[catalinosonesti]

hi
i need code for RCD 310 ,95128 + nec ....
regrads

[REZON]

hi
i need code for RCD 310 ,95128 + nec ....
regrads
Try code 0981

[catalinosonesti]

Try code 0981
work ,perfect ,thank you wery much ,please can you tell me wich bits use to pair nec because i try 000A30 but not pair with nec
thank s again
best regrads