help needed citroen c3 vin to pin

[jacques23]

hi can someone please asisit with citroen c3 pin from vin all tools fail too read pin lonsdor fvdi etc help will be appreciated vin nr vf7fckfvc28685926 thanks jacques

[alefabi2006]

read bsi o ecu dump

[brend]

hi can someone please asisit with citroen c3 pin from vin all tools fail too read pin lonsdor fvdi etc help will be appreciated vin nr vf7fckfvc28685926 thanks jacques


Read bsi/ecu eeprom.

[jacques23]

hi managed to read ecu flash with fvdi via obd2 please advise if it will work thanks jacques

[brend]

hi managed to read ecu flash with fvdi via obd2 please advise if it will work thanks jacques

More details about ecu.

[jacques23]

More details about ecu.
hi its valeo got the bsi as well but no idea how too read it with upa thanks for all the help so far tried a kess also on the car today it failed said awake error

[alefabi2006]

reads EEPROM BSI. NO FLASH

[jacques23]

here is bsi info

[jacques23]

hi so we need too split fusebox bord and bsi board ? i got upa and carprog

[brend]

Yours BSI eeprom must by 95128.
This pinout connection for all programmers.

[jacques23]

Yours BSI eeprom must by 95128.
This pinout connection for all programmers.
thank you so much appreciate going to read with upa just want to know on connection 3,7,8 do we solder all 3 wires or only 1 ? thanks jacques

[brend]

Yes...........

[jacques23]

hi upa give a range error when i read as 25c180556396

[brend]

25c180!!??

Must by 95128.

[jacques23]

upa dont have 95128 read on forum can read as 25c180 will carprog work?

[brend]

Maybe have 25128 its same like 95128.

[jacques23]

sorry 25c128

[brend]

sorry 25c128

25c128 its wrong!

Look better ,if yours programmer not have eeprom NR lokation like 95128 ,so 100% must by 25128.

I not,so.......use another programmer .

[jacques23]

only got 25c128 going too check carprog if it got the option



556404

[brend]

only got 25c128 going too check carprog if it got the option



556404

Carprog have this 100% !

[jacques23]

Carprog have this 100% !
have you got a connection diagram please mine a clone ive tried too read it says unknown version eeprom is all fffff

[jacques23]

hi brend can you please check if file is ok

[brend]

hi brend can you please check if file is ok

Its empty.All fffff

Check wires right pin location/conection.

[jacques23]

Its empty.All fffff

Check wires right pin location/conection.
hi can you check if my wiring correct carprog verify file is ok is there a way too get pin from cluster dump ?

[banelab]

long story short....Read ecu eeprom and ok

[jacques23]

do you know what eeprom its got its a valeo jp34 ecu starting to think this bsi corrupt with charger connected when you try too read pin instant economy mode battery ok but it keeps doing it

[jacques23]

ecu risky job am i right or wrong?

[brend]

Just need by carefully ,thats all.
Or desolder eeprom from bsi and read this.

[jacques23]

Just need by carefully ,thats all.
Or desolder eeprom from bsi and read this.
thanks going too split fuse box and bsi board only way too see if eeprom bsi is corrupted because carprog verify ok after reading but all ffffs thanks for all the patience and help appreciated i will report back

[brend]

thanks going too split fuse box and bsi board only way too see if eeprom bsi is corrupted because carprog verify ok after reading but all ffffs thanks for all the patience and help appreciated i will report back

Maybe not.
Carprog sametimes to do this crap like read ok, verify ok,but realy nothing read , and with dump all ok.

[jacques23]

i agree only good for opel security pin i got somebody with xprog and r270 will ask him to read eeprom for me once ive disasembled the bsi holding thumbs that the eeprom is ok

[banelab]

j34p 96150 u can open and read not so risk:crushed: 95160:peaceful:

[banelab]

your bsi is not ok,virgin then open j34p read pin and all ok

[banelab]

heat gun is one method and another is mini grinder with brush (not metal one)

[jacques23]

so i must write virgin file to bsi eeprom have you got a virgin file thanks jacques

[banelab]

Try with all ffff and use lexia

[jacques23]

Try with all ffff and use lexia
hi i dont have lexia only fvdi ,launch x431 diagun,fvdi i saw bsi swop

[brend]

For what you need pin code?

[jacques23]

For what you need pin code?
hi to code a key old keys transponder dead no pin read possible through obd my fvdi 2015 failed borrowed a fvdi 2018 failed lonsdor failed kess master failed car goes into economy with charger connected we checked all fuses wiring etc all units scan with launch and fvdi i did plenty citroens through obd first time i come across this usually a ten minute job battery is also 100 persent all faults in bsi that it shows is number plate lights and then it says anti theft faulty

[banelab]

Economy mode will exit when car is running.Just take pin and do a new coding.

[jacques23]

yip going too split bsi and read eeprom direct if that fails ecu and write ffffffto bsi is there a immo off solution for this vehicle ?

[banelab]

If u see vin in bsi then your eeprom in bsi cant be all fff.Remove eeprom from board and read it with carprog (u say that have) if it is corrupt file than all ffff and read eeprom from ecu,take pin but than u need lexia for config bsi.

[kiszka]

..........

[banelab]

J34p as I understand

[jacques23]

J34p as I understand
hi yes its j34p

[jacques23]

what's your ecu
hi it is jp34

[kiszka]

..........

[jacques23]

afternoon everybody just want to know which eeprom the right one too read thanks jacques

[jacques23]

read ecu eeprom
hi the ecu eeprom from the ecu is 95160 ?

[rob h]

hi the ecu eeprom from the ecu is 95160 ?
Some info, on part and car

[jacques23]

hi citroen c3 2006 ecu jp34 bsi valeo customer drove the car next morning car didn't start i checked the key transponder no response got a new key no pin code retrieval possible through obd 2 lonsdor, fvdi 2015 fvdi 2018 tried a kess master ass well checked all fuses wiring bsi eeprom didn't want too read on bench with carprog shows empty ive read both the ecu 95160 and bsi 95128 via upa on programmer boards off the pcbs to eliviate bad connection .both said success with upa thanks help will be appreciated

[jacques23]

citroen c3 bsi info

[PierreTheron]

Mate repair the old key . Replace the coil ...
Your files posted is not correct reads ...

[jacques23]

thanks pierre will try do you think the software is corrupted or am i not reading the eeproms correct ill replace the coil in the key and see what happens ive tested the ignition coil with vvdi key tool its functioning thanks for the help appreciate

[brend]

thanks pierre will try do you think the software is corrupted or am i not reading the eeproms correct ill replace the coil in the key and see what happens ive tested the ignition coil with vvdi key tool its functioning thanks for the help appreciate

Ask maybe help for read eeprom same friend,who know how need use programmer................:dontknow:

[jacques23]

hi brend i cant understand no connection errors in upa when i read also read says success and verify im using the board with the eeprom soldered to it dont know what im doing wrong then

[brend]

hi brend i cant understand no connection errors in upa when i read also read says success and verify im using the board with the eeprom soldered to it dont know what im doing wrong then

If eeprom desolder from ecu/bsi and read, its by empty immpossible ,because same data restore from flash and samething must by 100%.
So...... look better what its wrong in programmer or settings..............
Or yours upa programmer just totally crap.......

[jacques23]

hi i have finally read the ecu and bsi eeprom bins

[brend]

:celticparty::congrats:Amazing! You get right ..............:applause:

Pin code U97E or revers E79U.

[jacques23]

:celticparty::congrats:Amazing! You get right ..............:applause:

Pin code U97E or revers E79U.
thank you so much for youre patience :star::excitement:lol i didnt even sleep last night trying too get it right learning a lot with all the great friends here

[Fernandojose]

Boa tarde preciso do pin bsi delphi c3 vin VF7FC8HZC29166404....Obrigado