Opel CD30 unregister it

[kwansterp]

Hi
I need unregister for this Radio
OPEL CD30 by BLAUPUNKT
13190856
inside 95640


Thank you in advance

[bank]

Unregistered (https://mega.nz/#!YeZhGCKY!BkPOJmd2eXRKsoXkHvw6iZURsyQTh5n6YErl2-YxmJU)

[kwansterp]

This is a completely different file, from another radio.

[criollo]

7664 ------------

[shooting]

This is a completely different file, from another radio.


Here you go ;)

wbr

[bank]

This is a completely different file, from another radio.
Yes, exactly. It's a virgin dump for cd30 Blaupunkt YY

[kwansterp]

The pin 7664 is good but I can not deactivate my Op-com. Still display safe. FVDI has a message about unsuccessful deactivation.
I am probably trying to make a ready file from shooting.

[bank]

The pin 7664 is good but I can not deactivate my Op-com.
Use one of received virgin dumps, set correct config in mid speed can bus and pair using code from display

[shooting]

The pin 7664 is good but I can not deactivate my Op-com. Still display safe. FVDI has a message about unsuccessful deactivation.
I am probably trying to make a ready file from shooting.

Just use my dump and enjoy ;)

wbr

[kwansterp]

The shooting files and the bank are good. Every few seconds beep ... beep. I can not marry them with the display. My two Op-com can not make it. But I heard that it happens. I need to ask to pair files from the radio and display.
I'm sending a file from the display.

Borg 13208089 AT
93c56 x8bit

Thanks in advance

[bogege]

The password of the car should be:3507 Use it for marriage!

[kwansterp]

The pin is known to me, correct, but I have nothing to pair the radio and display with.
Can I ask for paired files for radio and display.

[shooting]

The pin is known to me, correct, but I have nothing to pair the radio and display with.
Can I ask for paired files for radio and display.

Just use OPCOM... 2 minute job ;)

wbr

[kwansterp]

My op-com 1.39 and 1.59 can not do it. I do not know why myself. Unless I'm doing something wrong.
EHU -> Prog .. -> activate protect -> PIN -> Successfully completed. I turn the radio off for about 1 minute and it still does not work.

[shooting]

My op-com 1.39 and 1.59 can not do it. I do not know why myself. Unless I'm doing something wrong.
EHU -> Prog .. -> activate protect -> PIN -> Successfully completed. I turn the radio off for about 1 minute and it still does not work.

What's on the display?

wbr

SEE BELOW:

CD30 Error Messages
===================

If you see "DISPLAY SAFE" permanently shown after 10 seconds,
this means that the Display has not been correctly programmed to the vehicle.

If you see "DISPLAY SAFE" flashing every 10 seconds, this means that the Display
is currently in Delivery Mode, and is now ready to be programmed to the vehicle
with a OBDII programmer.

If you see "RADIO SAFE" permanently shown after 10 seconds,
this means that the Radio has not been correctly programmed to the vehicle.

If you see "RADIO SAFE" and a beep every 10 seconds, this means that the Radio
is currently in Delivery Mode, and is now ready to be programmed to the vehicle
with a OBDII programmer.

[kwansterp]

I have currently in Delivery Mode (Radio Safe and a beep every 10 seconds). I uploaded your file and I can not pair the radio with the display by Op-com.
What am I doing wrong?

[shooting]

I have currently in Delivery Mode (Radio Safe and a beep every 10 seconds). I uploaded your file and I can not pair the radio with the display by Op-com.
What am I doing wrong?

Sometimes you need to disconnect the battery for 5 minutes.. try this next

wbr

[kwansterp]

Ok, I will try

[kwansterp]

None of this will be, my two Op-coms are not able to pair this radio.
I have tried many times, I have disconnected the battery for many minutes.
Can you get paired files for the radio and display?

[shooting]

None of this will be, my two Op-coms are not able to pair this radio.
I have tried many times, I have disconnected the battery for many minutes.
Can you get paired files for the radio and display?

It's just a CD30, your opcom will be the problem,

wbr

[kwansterp]

Yes, my opcom has a problem, but FVDI also does not pair.
Can you ask for modified files for the radio and display.
Manual work will be repaired.

[budata]

Change the file to the display,maybe blocked...! :)
https://1drv.ms/u/s!An2tr1M8gwVrjlWg3JOMexnl020Y

[shooting]

or better use this... original modified... (Above is not correct)

wbr

[audiopoint]

need unregister dump

[castin]

Meybe like me - security Time locked. Check in GID measuring blocks: Security Wait Time - "In Progress", then must wait on switch ON.

[shooting]

need unregister dump

Here you go... original unregistered

wbr

[budata]

Here..https://1drv.ms/u/s!An2tr1M8gwVrjlYeQmmX4XhTesz1

[shooting]

Here..https://1drv.ms/u/s!An2tr1M8gwVrjlYeQmmX4XhTesz1

This is incorrect... 100% not an unreg file... if you do not understand this model don't post..

wbr

[budata]

This is incorrect... 100% not an unreg file... if you do not understand this model don't post..

wbr

my mistake, I'm messing with Delphi......I apologize !

[bank]

need unregister dump
You need to check security wait time and mid speed can bus.
I can help you to pair via teamviewer even using opcom.

[bank]

I'm sending a file from the display.

Borg 13208089 AT
93c56 x8bit



Here (https://mega.nz/#!UGQn0aLR!oS0fFfFK_g4wvTI2GoOPbucykZBde4_VhEeSo5S GOO0) is virgin dump for your display
Can pain using any code

[shooting]

Here (https://mega.nz/#!UGQn0aLR!oS0fFfFK_g4wvTI2GoOPbucykZBde4_VhEeSo5S GOO0) is virgin dump for your display
Can pain using any code

Look at Post#23 .. maybe you think yours is better?

wbr

[bank]

Look at Post#23 .. maybe you think yours is better?


Sorry if it's the same, I don't verify your dump.
I just post 100% working virgin dump

[shooting]

Sorry if it's the same, I don't verify your dump.
I just post 100% working virgin dump

Just read the thread you are posting in...

wbr

[bank]

Topicstarter has display and radio from different pairs.
Virginised dump for radio hi already receives but can't pair using code from display.
So, it can be 2 causes of problem
1. Security wait time in display
2. Wrong settings in MidSpeedCanBus. As example, ECC marked as "Present" in radio

Any cheap opcom can make a pair

[shooting]

Topicstarter has display and radio from different pairs.
Virginised dump for radio hi already receives but can't pair using code from display.
So, it can be 2 causes of problem
1. Security wait time in display
2. Wrong settings in MidSpeedCanBus. As example, ECC marked as "Present" in radio

Any cheap opcom can make a pair

Any cheap opcom can't repair all unregister/register .. and only a fool thinks the Chinese software and the real software are the same.
Ver 1.59 Chinese soft is a rebadged Ver 1.xx original, we are now at Ver 1.66 original but this would kill a clone.
Also V6 boards of Opcom clone have fake chips too and can't be upgraded.
Sooooo a real tool can set/reset all features and displays without any editing of files, unlike clone which need help.
The tool the user uses really matters.
As to the firmwares, you need to edit the original not replace with an unknown, because of other features you have not considered.
Displays hold more information than you think, also the radio's have differences.. this is why no two dumps are identical.

wbr

[bank]

you need to edit the original not replace with an unknown, because of other features you have not considered.
Displays hold more information than you think, also the radio's have differences.. this is why no two dumps are identical.

I know displays and radios contains more info then just pin code and pairing info, such as code index, audio index, can bus config, variant config, VIN etc.
But if one of items is divorced, another one can be divorced too using any opcom. Ypu just need to do more manipulation instead a simple reset.

Also, as you say there is wide variety of radios and displays, but thea all "marked" by alpha code. In upper post it was "AT" for display and "YY" for radio.
And my proposed dumps are fully compatible.
Even if you make radio divorced, it's not always working solution because, as you know, you need to set correct can|variant settings to make it working proreply. TECH2 do this step by step during programming procedure, but opcom not.

So any cheap opcom can disable protetion using correct code to make radio or display divorced, and I was doing it many timeswith success.

[bank]

Any cheap opcom can't repair all unregister/register .. and only a fool thinks the Chinese software and the real software are the same.
Did you know Chinese opcom can work with original software v15 and later? :) All you need is software key generated for your device ID

[shooting]

Did you know Chinese opcom can work with original software v15 and later? :) All you need is software key generated for your device ID

You are confusing this with Euro clone with read/write PIC processor, Chinese clones use a write once PIC

wbr

[bank]

You are confusing this with Euro clone with read/write PIC processor, Chinese clones use a write once PIC

I’m not confusing.
I have Chinese clone with as you said read/write pic”, and also have opcom with write once pic. First can work with original software, but both can work with hacked version of software and both can deactivate protection

[kwansterp]

Everything is working. I uploaded files from post # 5 and # 23 from shooting and everything works.
The problem was in the display. He was wrong to set Middle Can and time after bad typing car pass.
My two Op-com is ok.
Thank you all for your help and advice. Especially shooting and bank deserved a big beer :)