View Full Version : Vw 06A906018EQ ECM IMMO OFF
dd1
28th September, 2018, 12:38 PM
Hi everyone, my friend's car is a vw and would like to immo off his ecm. So far I have the ecm part number. Can anyone tell me what type of ecm is this and what's the immo info located? I think it should be an eep but which ne I don't know. Thanks in advance
slawcio26
28th September, 2018, 03:30 PM
if vw Beetle 2,0 bosch motronic 5.9.2 ?? then eeprom 24c02
dd1
28th September, 2018, 05:06 PM
Thank you. If I read an post here, can anyone immo off for me????? Thnx in advance
brend
28th September, 2018, 05:15 PM
Put original dump.
dd1
28th September, 2018, 05:53 PM
This is strange. I can't read the eep. I have tried 2 adaptores and both give me an error BAD CONTACT on pin7 !!!!!! I'm using ELNEC original. What gives??????? I have inspected and the contacts are good
dd1
28th September, 2018, 06:17 PM
ok, i have it
brend
28th September, 2018, 07:46 PM
Press magic button for more power.........:bounce:
Pass look in PM.
IMMO OFF 100%.
kiszka
28th September, 2018, 08:53 PM
..........
dd1
2nd October, 2018, 06:44 PM
Press magic button for more power.........:bounce:
Pass look in PM.
IMMO OFF 100%.
sorry BREND, yours did not work and i am getting immo codes in the module, plus 2 other codes. trying KISZKA solution, lets see what happens
kiszka
2nd October, 2018, 09:41 PM
..........
dd1
3rd October, 2018, 06:00 PM
it will be 100% ok :driver:
thnx KISZKA, but yours worked only one day. the immo code has come back plus the coding error fault codes and the car wont start again. any idea???????
brend
3rd October, 2018, 07:39 PM
Dump from you is original or from another ecu?
rafal
3rd October, 2018, 07:43 PM
thnx KISZKA, but yours worked only one day. the immo code has come back plus the coding error fault codes and the car wont start again. any idea???????
by my experience if Kiszka or Brend did immo off so must 100% work. check what is wrong in car.
dd1
4th October, 2018, 04:10 PM
Dump from you is original or from another ecu?
hi everyone, the ecu is not the original, we have another used ecm that want to use on this car.
kiszka
4th October, 2018, 04:12 PM
..........
dd1
5th October, 2018, 11:34 PM
upload eeprom
hi, i have the original file here, in #6 post. please check it
kiszka
6th October, 2018, 12:00 AM
..........
dd1
6th October, 2018, 12:19 AM
ok, what needs to be done in order to have a used module work on this car????? so that the engine control module can work with no IMMO. Its a used module and the original is no present. thnx
kiszka
6th October, 2018, 07:31 AM
..........
dd1
6th October, 2018, 03:31 PM
show me the reading after an ecu reset
Hi, i dont understand, what reset? We just plugged in the module and the car started. Have not done any coding. Only throtle adaptation and that is it
yugo45
6th October, 2018, 03:51 PM
Hi, i dont understand, what reset? We just plugged in the module and the car started. Have not done any coding. Only throtle adaptation and that is it
What car is it?
dd1
6th October, 2018, 05:05 PM
What car is it?
Vw bettle 2001.
yugo45
6th October, 2018, 06:34 PM
Vw bettle 2001.
Is it manual or Auto transmission ?
immokill
6th October, 2018, 07:22 PM
when car wont start what are DTC in ecu? Maybe Relay for ecu and relay for pump is bad but post Error codes when car wont start
dd1
6th October, 2018, 08:10 PM
when car wont start what are DTC in ecu? Maybe Relay for ecu and relay for pump is bad but post Error codes when car wont start
HI EVERYONE, the CAR started fine when i coded the immo OFF, but the next day again. when it started i had coding errors coming on the check engine.
dd1
6th October, 2018, 08:13 PM
Is it manual or Auto transmission ?
automatik trans
dd1
9th October, 2018, 07:01 AM
I just purchased an ecm for 1999 with no immo already. Plug and play. Thanks to everyone that tried to help
12 volt tech
23rd February, 2019, 09:30 AM
2001 Vw Beetle immo off please 0261206409
rafal
23rd February, 2019, 10:04 AM
2001 Vw Beetle immo off please 0261206409
here you go.............
where have you been since 2018?
you are not helpful for others m8
12 volt tech
23rd February, 2019, 10:44 AM
Work Good thanks
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.