PDA

View Full Version : EDC15V ECU Reading problem



vrsho
29th September, 2018, 01:47 PM
Hi,

i have a problem with ECU Reading on VW New beetle EDC15V - old connector. I tried to read it with Galetto and Kess but without success. Galetto crashes and kess sends Wake up error. Tried it with OBD and on bench. What did i missed here? Here is the pin-out of ECU.

kaadzis
29th September, 2018, 02:06 PM
ecu number please. probably its old ecu with 2x 27c1001 eproms. then only desoldering and new chips

vrsho
29th September, 2018, 02:14 PM
The number is: 038906018AP. Thanks.

H.Wessel
29th September, 2018, 02:24 PM
Like old MSA15, only solder job for this ecu

vrsho
29th September, 2018, 02:31 PM
Yes, its an MSA15 - i see it now. There are 2x b58911 EEPROMS. I guess these two are only readable. So, what is the procedure? Reading it, remapping the files and then writing it back on some M27C1001 EEPROMS or? Thank you guys.

raceshadow
29th September, 2018, 02:36 PM
Hi,

i have a problem with ECU Reading on VW New beetle EDC15V - old connector. I tried to read it with Galetto and Kess but without success. Galetto crashes and kess sends Wake up error. Tried it with OBD and on bench. What did i missed here? Here is the pin-out of ECU.

2x 27c010 inside this MSA15. Only soldering. Read old chips with programmer. Make remap and write on new chips. I'm using 29f010, but you can use a different type.

560157

vrsho
29th September, 2018, 04:25 PM
2x 27c010 inside this MSA15. Only soldering. Read old chips with programmer. Make remap and write on new chips. I'm using 29f010, but you can use a different type.

560157

I have 2x b58911 inside. So i can put this 29f010? The pinout is same? Thanks.

raceshadow
29th September, 2018, 10:15 PM
I have 2x b58911 inside. So i can put this 29f010? The pinout is same? Thanks.

Yes, you can use 29f010.

Rokosius
26th October, 2018, 04:01 PM
it is the same procedure if my ecu code are 038906018FB?

morgano
26th October, 2018, 04:19 PM
Those old ......018 ecus are same, desolder job.

Rokosius
26th October, 2018, 04:33 PM
thanks for fast answer!

gege974
26th October, 2018, 09:27 PM
hi
I've already seen some adapt edc15mv instead of msa. But there is a lot of work

may there be an adapter?

mrchip
26th February, 2019, 12:58 AM
I need pinout of this ecu to diagnostic on bench .. it is an edc15V or msa15 ecu ?
please share +12v , k-line-ground pins

038906018bp
0281001848

dominik.m
26th February, 2019, 01:12 AM
Here. MSA15 pinout.

mprog
26th February, 2019, 01:21 AM
Now You can buy SST39SF010, remember HHH and LLL right places

BR

mrchip
27th February, 2019, 08:03 AM
Here. MSA15 pinout.
thank you Dominik

kaverosaez
10th May, 2020, 06:45 PM
Good Afternoon.
I am trying readind 038 906 018 GM but I canīt find information about it.
Could I read this ecu by pinout?
Thanks

familiozo
10th May, 2020, 07:05 PM
Good Afternoon.
I am trying readind 038 906 018 GM but I canīt find information about it.
Could I read this ecu by pinout?
Thanks
018 is msa 15 with 2 plcc need programmer and hotair gun read this thread.

oscartomas20
11th May, 2020, 01:40 AM
Try whit MPPs v16 is possible sometimes whit obd !

bodzio012
11th May, 2020, 07:59 AM
Try whit MPPs v16 is possible sometimes whit obd !

MSA15 is impossible

ZiZiTun
11th May, 2020, 09:03 AM
MSA15 you can not read via OBD. Just work with programmer, hot air and soldering. Most you need new eprom, just some ECUs from AUdi have old flash, which you can reprogaming. Dont forget position of H and L eprom. 713364

kaverosaez
11th May, 2020, 07:25 PM
I want to read flash to remap, not eprom

thanks

dehacko
11th May, 2020, 07:42 PM
flash chip read/ write only desolder my friends
use programer tl minipro 866 ;)

kaverosaez
11th May, 2020, 07:52 PM
thansk you

sonny21
24th March, 2021, 12:32 PM
hi guys,

can upa program m27c1001 chip(passat b5 ahu) ? and i saw some guys selling programed chip on ebay ? is ok if i order preprogramed chip and then swap them ? thx