OPEL CORSA D PIN from TACHO

[kubuswujo]

Can someone help with reading PIN code from tacho CORSA D?

EEprom was 080D0WQ.

Thanks in advance
Kuba

[bank]

4999 or 9499

[kubuswujo]

i need this code to adapt new ecu in car i had new ecu and pin for new ecu i reset it its ok.
But i try to type
4999 or 9499

In immo as security code and it is not working... pin should be same in tacho and immo module as i think...

I tried several times but always wrong security code...
Can someone check?

EDIT:
I found the right PIN.

I read the PIN CODE FROM Instrument cluster using Autel via OBD. It shows:
9949.

Ok this PIN CODE works but only for Instrument cluster. But when i go into
BODY>Immobilizer>Programing>Security code>>

I always get :"Wrong security code" I must add that i do have oryginal OP-COM.
In Instrument cluster PIN 9949 OK, but in Immobiliser not ok... ;/ ;/ ;/

Is it possible that car has different PIN in immo and in Instrument cluster?

[kubuswujo]

I try to read PIN code from old ecu using CARPROG
ecu is ME7 6.2 but carprog shows PIN:
A3C4

Immo sync data:
33D6349A5F734C36383834307D6ABB45A3C480F05C383A55

Is it possible that PIN has Letters not numbers?
568928


If i make read all it does try to read but after finish does not show anything.
Read dump also same.
"Searching unlock byte" and finish and noting new.

[dumitrescu12]

Could you please let us know what you want to do ?

If you want to change the dash, you need the security code from the new dash and for the old one ...

Let us know your situation and I will try to help you !

[kubuswujo]

Sorry i wanted to adapt new Ecu in car.

I have old ecu and have readed Pin from it: 9949
I have Tacho from car Pin is 9949
I have new ECU that i want to adpadt its 1707


And now, there is no problem to:
reset old ecu,
reset new ecu.
write security code in tacho (obly for try if pin is ok)
But when i go into Body immobilizer and try 9949 Pin i got a wrong security code

[rafal]

have you tried reset by carprog?

http://www.digital-kaos.co.uk/forums/showthread.php/504975-ME7-6-2-can-astra-h-cannot-reset

[super jumbe]

Remove old chip from old ECU and replace to new ECU....

[kubuswujo]

Here is an inside of ECU please tell me where here is EEprom?
I cannot identify EEPROM here.



569438

[Faraday]

IMHO In this case best to read BCM for pin

[kubuswujo]

Ok, here is a BCM where here is eeprom to read?
569447569448

[rob h]

70F3238+93C86 70F3379+93C86569453

[abbaci]

i use fvdi or carprog . what is ecu reference plz

[super jumbe]

Here is an inside of ECU please tell me where here is EEprom?
I cannot identify EEPROM here.



569438



Sorry I thought this was Corsa D 1.3 CDTi

.B.q.*÷..Ü.�.ÿ‚.ÿ..…².t.%.ÈM�:Ã'..¾.4....#.2. \J.iË. e�}...V.iÙ†¯&•…².t.%.ÈM�:Ã'..¾.4....#.2. \J.iË. e�}...V.iÙ†¯&•ÖB9994..0W0LDS6L88044147.0........ÖB9994..
0W0LDS6L88044147.0................................ ..ÍKJÈçìÍKJÈçìå�

Prited 9994
Converted: 9949 if it came from the same car live ignition on for 40min should let you go in.

[dkgti]

can you help....i need pin code uploaded file is dump from instruments

[Stopro92]

@dkgti - 7570

[Talleresmalaga]

Sorry i wanted to adapt new Ecu in car.

I have old ecu and have readed Pin from it: 9949
I have Tacho from car Pin is 9949
I have new ECU that i want to adpadt its 1707


And now, there is no problem to:
reset old ecu,
reset new ecu.
write security code in tacho (obly for try if pin is ok)
But when i go into Body immobilizer and try 9949 Pin i got a wrong security code

Good afternoon, why do you change your ecu?


if it is because the vehicle did not start, it could be problems with the cim module and it is not ecu problems and it continues with the error ...


You can use carprog to read old ecu and modify the new one, without having to use opcom to pair


Process:
connect old ecu to the vehicle, put the contact, read with carprog, at the top, this eeprom, enter and save the reading.


leave the screen open


disconnect the contact, change the ecu and connect the scrapping contact and write


the data of the pin and cinclonized must be cloned


start the vehicle and have a beer to our health


if you have a cloned ecus the problem persists change cim module


regards

[kcsaude]

H iguys I need someone to help please I have a eeprom dump file from ipc corsa d 1.0 08 plate
dump file attached . Thanks!!!

[kcsaude]

Hi guys just extract the dump file from my IPC some one please can help me find the pin code from it ... file attached,

thanks

[Stopro92]

Bad dump :) send dump tacho 35080 :)

[kiszka]

Hi guys just extract the dump file from my IPC some one please can help me find the pin code from it ... file attached,

thanks

it is imperative to read the eeprom as 35080 !
you can not help a person
which does not listen to what is being said
if it is difficult for you, then find yourself another job
https://www.digital-kaos.co.uk/forums/showthread.php/462322-Opel-Corsa-D-2007-pin-from-dump
https://www.digital-kaos.co.uk/forums/showthread.php/221160-2008-Corsa-D-Pin-Code

[Tibi1983]

Szia.
Kérem, segítsen, szükségem lenne egy biztonsági kódra.
Opel corsa d 2007 vintage
1.3 motorkód: DTH: z13DTH1768125 Kérem


, segítsen ...

[brend]

Without dump only good luck!


Hi there.
Please help I would need a security code.
Opel corsa d 2007 vintage
1.3 Engine code DTH: z13DTH1768125


Please help ...

[Tibi1983]

Unfortunately, what you wrote a link to is invalid.

[Tibi1983]

Itt van az olvasott fájl.
Köszönöm a segítséget.


Hello.
Please help, I need a security code.
Opel corsa d 2007 vintage
Engine Code 1.3: DTH: z13DTH1768125




Please help ...

[rafal]

post eeprom m8................................

[Tibi1983]

[QUOTE = rafal; 4052514] post eeprom m8 ................................ [/ QUOTE]
What does that mean?
Can't find the security code from here?

[sebage]

This means that the Security Code is stored in eeprom.
You posted the contents of the flash ... maps.

You need to read and put here the content of eeprom something like 95320

[Tibi1983]

[QUOTE = sebage; 4054239] Ez azt jelenti, hogy a biztonsági kódot az eeprom tárolja.
Ön közzétette a flash ... térképek tartalmát.

El kell olvasnia és ide kell raknia az eeprom tartalmát, például 95320 [/ QUOTE]







Please explain. How to read? Where is it located?

[brend]

ENGLISH!!!



[QUOTE = sebage; 4054239] Ez azt jelenti, hogy a biztonsági kódot az eeprom tárolja.
Ön közzétette a flash ... térképek tartalmát.

El kell olvasnia és ide kell raknia az eeprom tartalmát, például 95320 [/ QUOTE]







Please explain. How to read? Where is it located?

[Dobermann]

i need this code to adapt new ecu in car i had new ecu and pin for new ecu i reset it its ok.
But i try to type
4999 or 9499

In immo as security code and it is not working... pin should be same in tacho and immo module as i think...

I tried several times but always wrong security code...
Can someone check?

EDIT:
I found the right PIN.

I read the PIN CODE FROM Instrument cluster using Autel via OBD. It shows:
9949.

Ok this PIN CODE works but only for Instrument cluster. But when i go into
BODY>Immobilizer>Programing>Security code>>

I always get :"Wrong security code" I must add that i do have oryginal OP-COM.
In Instrument cluster PIN 9949 OK, but in Immobiliser not ok... ;/ ;/ ;/

Is it possible that car has different PIN in immo and in Instrument cluster?

Hello my friend,

i have exactly same problem.

i have a corsa d with 1.4 66kw me7.6.2 ecu

i want to change ecu because its damage.

i read pin with opcom from instrument cluster >>> pin is 8216

code worked in instrument but not in immobiliser.

i think this code should be the same. old ecu i cant read because its dameage and no comms..

what to do now ? i dont have car pass but maybe its possible to get it from dealer.

but i have the code from instrument, but did not work in immobiliser.

i can read eeprom from cluster too but is this nessessary ?

thanks

best regards

[Panathaole]

extract from cid, or easiest way if you have fvdi, use it.....

you must extract pin code and from donor ecu to reset it.... try with fvdi or carprog.....

[Dobermann]

extract from cid, or easiest way if you have fvdi, use it.....

you must extract pin code and from donor ecu to reset it.... try with fvdi or carprog.....

thanks for help. the doner ecu is resett . i did it with carprog orignal.

problem is only that pin readed from instrument cluster with opcom not work in immobilizer to pair the new used ecu.

pin code worked for login in instrument but not in immobiliser where the funktions are in to pair the new ecu.

and i think normally the pin from instrument musst be the same for immibiliser !?

i think i will take off tacho and read pin from eeprom 35080

[rafal]

Reset ecu by carprog= ecu bricked
Carprog for read pin ok not for reset
fvdi reset ok
Opcom reset ok

[Dobermann]

Reset ecu by carprog= ecu bricked
Carprog for read pin ok not for reset
fvdi reset ok
Opcom reset ok

Hello thanks for answer.

reset ecu is not the problem for sure. i reset with opcom too .

ecu is reset .

problem is security code in immobilisieer not work !

in instrument cluster work.

i have to check later the immo waiting time. maybe this is the problem.

code from instrument should be the same for immobilisier

[rafal]

Hello thanks for answer.

reset ecu is not the problem for sure. i reset with opcom too .

ecu is reset .

problem is security code in immobilisieer not work !

in instrument cluster work.

i have to check later the immo waiting time. maybe this is the problem.

code from instrument should be the same for immobilisier

i understood u................ but if ecu reseted by CP 1st - ecu bricked

[Dobermann]

i understood u................ but if ecu reseted by CP 1st - ecu bricked

i have original CP ecu is not bricked. ecu is ok.

opcom read ecu and reset ecu was possible with opcom without any problems.

[rafal]

i have original CP ecu is not bricked. ecu is ok.

opcom read ecu and reset ecu was possible with opcom without any problems.

do as u want...............
remove eeprom from dash for check pin if is 100% correct
but if u can log to dash by pin - probably good
good luck

[Dobermann]

do as u want...............
remove eeprom from dash for check pin if is 100% correct
but if u can log to dash by pin - probably good
good luck

yes this is exactly what i thought too

i will read eeprom from dash and check pin and check immo waiting time again.

but its like you said if login to instrument is ok the pin should be correct.

[rafal]

yes this is exactly what i thought too

i will read eeprom from dash and check pin and check immo waiting time again.

but its like you said if login to instrument is ok the pin should be correct.

sure - i wrote all as i should on this subject.............. i bricked ecu by CP by self even ori - but you are looking for something where shouldn't

[Dobermann]

sure - i wrote all as i should on this subject.............. i bricked ecu by CP by self even ori - but you are looking for something where shouldn't

was is it cp china or an original cp ?

i testet some older me155 ecu from astra let20 and reset worked with ori cp

[rafal]

was is it cp china or an original cp ?

i testet some older me155 ecu from astra let20 and reset worked with ori cp

i tested ori and clone , with older ecus ok - with me7.6.2 fail

[miroopel]

IPC was replaced without reset and programming. IPC pin code is different from BCM. For correct Pin code read BCM, Radio, DIS, Airbag.

[Dobermann]

IPC was replaced without reset and programming. IPC pin code is different from BCM. For correct Pin code read BCM, Radio, DIS, Airbag.

Hello,

i solved my problem today.

But Pin code was not different from IPC to BCM and IMMO

As first i checked immo waiting time. that was active 00.10.00 so i cant login to immo.

i tryed this >> with the readed login code from Opcom >> login to BCM worked :victorious: after this login to IPC worked too after this check again immo waiting time > suprise now not active 00.00.00

tryed to login with the readed code from opcom and look there im in ;-)

paired new reseted ecu and car start !

i take off the tacho to check PIN code

read it with carprog M35080 / >> 080D0WQ

in eeprom file are the login code swapped. login readed from opcom 8216 in eeprom >> 2861

so maybe opcom automatic swapped or in the eeprom the login is stored swapped.