View Full Version : Renault Clio 1.5dci ddcr immo off
marcin7091
9th November, 2018, 12:39 PM
Hi all
I need help with immo off for ddcr 1.5 dCi
Eep 95080
Ddcr 80925B
8200176975
Thanks and regards
immokill
9th November, 2018, 02:59 PM
i need it to but thin it is not possible
aandroma
9th November, 2018, 04:41 PM
Only with emulator
baltazar3
9th November, 2018, 06:27 PM
Only with emulator
NOT only m8...here is another way....no pw ...for all.
klonone
10th November, 2018, 04:40 PM
Hello, i write eprom Immo Off file. And write protecttion with upa , work perfect
brayanrios
10th November, 2018, 06:37 PM
FRIEND TRY THIS FILE HAVE IF YOU WORK
FRIEND TRY THIS FILE HAVE IF YOU WORK
worldofchiptuning
20th May, 2019, 09:50 AM
Hello, i write eprom Immo Off file. And write protecttion with upa , work perfect
hello
which file eeprom ???
thx
klonone
25th June, 2019, 07:14 AM
this file , protect bytes whit upa . and work perfect
regards
daten
20th August, 2019, 12:43 PM
Hi, has anyone managed to work with the klonone file?
aandroma
20th August, 2019, 03:21 PM
Clone file Not work
jodank
3rd September, 2019, 09:12 PM
Hi!
Is it possible to immo off this ecu?
Delphi
DDCR 80945A
Serial No.: 0823558
8200212348
HOM8200222917
This is from a Clio 1.5DCI 2003.
Thanks.
Master8
9th October, 2019, 11:42 AM
this file , protect bytes whit upa . and work perfect
regards
hello
I tried this file..... doing bytes protection in the status register.. you forget you should bypass starting relay because will not operate anymore
however..... wasted time, this solution doesn't work for me. Car cranks but doesn't start. Led light fast blinking on dash.
jorgecos
4th November, 2022, 05:24 PM
hola buenas tardes. quiero felicitar al immo off 95080 de la ecu ddcr y funciona muy bien. solamente no puedo cargar los codigos de los inyectores.
kppow666
23rd May, 2023, 07:22 AM
I have eeprom 25080 can I use the file from there? 8C protection 00 or FF does not work.
kppow666
24th May, 2023, 07:50 AM
I don't think that immo is only in flash. because I removed the eeprom connected the immo coil. and the immo system read the code from the key and the immo led went out and the engine could be started. immo system works normally without eeprom. only the gas pedal did not respond, so according to that it seems to me as if the immo was in the flash. as it is with the ems3134 and it is also possible to turn it off in the flash
danielif
24th May, 2023, 09:18 AM
Immo is in UCH, and in ECU motor EEPROM hawe the Synkhro.
kppow666
24th May, 2023, 04:28 PM
that's what i thought too. but why when eeprom is removed. does the ear synchronize even without eeprom? and the engine can start. if the eeprom is removed and I disconnect the transponder coil, the engine will not start.
Powered by vBulletin® Version 4.2.5 Copyright © 2025 vBulletin Solutions Inc. All rights reserved.