PDA

View Full Version : CITROEN JUMPER 22HDI SID208



immokill
13th November, 2018, 02:45 PM
Hello

Please need instruction how ro read this ecu . I have KTAG and only can be found under

Ford Transit SID 208 .

Please I need instruction how to patch this ecu or how to read it with KTAG ?


Thanks


Regards

sdtsedat
13th November, 2018, 02:54 PM
Search under protocols and look under SID208 PSA

teerak2uk
13th November, 2018, 02:54 PM
What year is it

voltechcar
13th November, 2018, 03:45 PM
K-tag do it by obd, eep + flash, voltage 13,5-14v and go

teerak2uk
13th November, 2018, 05:00 PM
How does ktag do eeprom by obd then???

voltechcar
13th November, 2018, 07:20 PM
operation the same what in boot but by obd.

immokill
13th November, 2018, 07:57 PM
I dont understand KTAg says to plug in obd cable in car to se what sw is ecu I dont have that OBD Cable for ktqg . What kind of cable is that can i read standar way pinout or not???

Regards

immokill
13th November, 2018, 08:01 PM
https://uploads.tapatalk-cdn.com/20181113/9e8ae5d7c0b2d6de38234a81ae162cb3.jpg

This is what I saw???


Sent from my iPhone using Tapatalk

teerak2uk
13th November, 2018, 08:01 PM
I dont understand KTAg says to plug in obd cable in car to se what sw is ecu I dont have that OBD Cable for ktqg . What kind of cable is that can i read standar way pinout or not???

RegardsEven if you had it after id it will prompt you to do via boot

Clone or genuine also pinout for ktag obd cable is in the forum I think

immokill
13th November, 2018, 08:02 PM
Can someone explain

immokill
13th November, 2018, 08:02 PM
So i can do it via boot mode


Sent from my iPhone using Tapatalk

teerak2uk
13th November, 2018, 08:04 PM
So i can do it via boot mode


Sent from my iPhone using TapatalkYes and needs good psu

immokill
13th November, 2018, 08:06 PM
Ok a have good suply

And ordinary what is PATCH that is my problem?

teerak2uk
13th November, 2018, 08:13 PM
Patch is so you can read/write flash over obd

No point if you open it and do via boot

teerak2uk
13th November, 2018, 08:13 PM
What year is this vehicle and is your tool clone

immokill
13th November, 2018, 08:27 PM
2010 PSA van with fiord injection SID208. . I heard that it must be over 13 V. powe suply and it will work with clone Ktag red pcb .

teerak2uk
13th November, 2018, 08:29 PM
Yes it will13.5v 3amp min

Ktab obd cable

144300T108 pinout :

KTAG_DB15 ---> OBDII

11 ------------> 04 ; 05 (Ground)

07 ------------> 06 (CAN_H)

14 ------------> 07 (K-Line)

15 ------------> 14 (CAN_L)

05 ------------> 16 (Battery Power)

I've not tried this cable though

immokill
13th November, 2018, 08:31 PM
I will take a chance to do with ktqg clone pcb via boot mode .
rhanks

teerak2uk
13th November, 2018, 08:34 PM
I will take a chance to do with ktqg clone pcb via boot mode .
rhanksWill be fine PSA but after 2013 will struggle prt change's

voltechcar
13th November, 2018, 09:39 PM
obd protocol have only genuine, china shit have only boot read

immokill
14th November, 2018, 06:04 PM
Magic did it by obd so problem solved friend did it with latest magicpro

immokill
17th November, 2018, 05:19 PM
Solved and ktag diidnt id it wirh 14v 5amp power . I measured on cables on bench on orange cable i uave 12.6max why if I puted main ktag power to 14v ?

teerak2uk
17th November, 2018, 05:38 PM
Solved and ktag diidnt id it wirh 14v 5amp power . I measured on cables on bench on orange cable i uave 12.6max why if I puted main ktag power to 14v ?Maybe your clone needs rework

immokill
17th November, 2018, 05:45 PM
I t is red pcb reworked . Read edc17 good read bmw good vag med17 . Thanks for info i will take aprt and look where is my 14v going to....
Is there any picture what to rework and what is usualy problem on ktag power suply?

teerak2uk
17th November, 2018, 05:48 PM
Did you try to power ECU direct?
Also not sure if 5amp is enough the supply I use is 15-20amp

immokill
17th November, 2018, 05:52 PM
Did you try to power ECU direct?
Also not sure if 5amp is enough the supply I use is 15-20amp
15 20 A ??????
Power ecu direct and put can high low and not powe on ktag?


Sent from my TELEFON

teerak2uk
17th November, 2018, 06:06 PM
15 20 A ??????
Power ecu direct and put can high low and not powe on ktag?


Sent from my TELEFONMy psu supplies upto 20amp

Yes power at ECU can hi/low via ktag

bersch8688
18th November, 2018, 07:18 AM
Use Power direct to ECU -> 12V & GND to the ECU Pin's and Can HI & Can LO from Ktag

carmageddon
18th November, 2018, 07:57 AM
i did many sid 208 ford but i used always supply 12V 2A!

macako6
18th November, 2018, 10:26 PM
Forget the cloned tools for this ecu, it does not work, clone Ktag on this ecu. Ktag genuine this ECU (SID208) works through the OBD without any problem.
Only information is already available, and Ktag genuine can sometimes make a problem and report an error (no communication).
But when everything is repeated (re-read) the operation then passes and there is no problem, I do not know why this is happening.
I use a voltage regulator of 14V and 5A.
For this problem, I have contacted Alientech and their response is "Change the voltage regulator" power supply.