View Full Version : Passat 1.8 20v needs warm up address map!
ponto33
25th November, 2018, 04:02 PM
Hi!!
I need a help to found the warm up map of Passat 1.8 20v, its possible that is 00B48A, its correct?
And in TLST.0 / TLST.1 (074E8 / 074F6), is just one point? its not a map 1x7? And to decrease injection time have to down or up the point?
thanks!
:)
icezero2010
25th November, 2018, 08:31 PM
Hi!!
I need a help to found the warm up map of Passat 1.8 20v, its possible that is 00B48A, its correct?
And in TLST.0 / TLST.1 (074E8 / 074F6), is just one point? its not a map 1x7? And to decrease injection time have to down or up the point?
thanks!
:)
u must post ori file without that nobody can help u
best with info about Ecu
hw number
bosch number
software number
ponto33
26th November, 2018, 04:24 PM
u must post ori file without that nobody can help u
best with info about Ecu
hw number
bosch number
software number
Ok! i will post here!! I will check!
ponto33
28th November, 2018, 10:54 PM
8d0 907 558 S
0 261 204 956
u must post ori file without that nobody can help u
best with info about Ecu
hw number
bosch number
software number
ponto33
29th November, 2018, 12:21 AM
now the ecu is immo on!!! I write the immo off file and the immo still block!
icezero2010
29th November, 2018, 03:25 AM
now the ecu is immo on!!! I write the immo off file and the immo still block!
06f00;Startgrundmenge;1x1
06f0e;Startgrundmenge;1x1
0b48a;Kennfeld für Warmlauffaktor;6x8
ponto33
29th November, 2018, 05:20 AM
Nice!!
Thanks man!
Startgrundmenge is 16bits right?
06f00;Startgrundmenge;1x1
06f0e;Startgrundmenge;1x1
0b48a;Kennfeld für Warmlauffaktor;6x8
ponto33
29th November, 2018, 05:26 AM
For the immo off i will open a new topic and will post the original file and the immo off file that i use and still block
http://www.digital-kaos.co.uk/forums/showthread.php/705270-IMMO-OFF-Passat-1-8-20v-ADR-Engine-8d0-907-558-S-0-261-204-956?p=3434564#post3434564
[QUOTE=icezero2010;3431578]
icezero2010
29th November, 2018, 11:14 AM
For the immo off i will open a new topic and will post the original file and the immo off file that i use and still block
http://www.digital-kaos.co.uk/forums/showthread.php/705270-IMMO-OFF-Passat-1-8-20v-ADR-Engine-8d0-907-558-S-0-261-204-956?p=3434564#post3434564
[QUOTE=icezero2010;3431578]
Yes 16 bit
But I don’t know what u will do ?
I nave never mod this maps also not with 1000 injectors
Gesendet von iPhone mit Tapatalk
ponto33
29th November, 2018, 03:05 PM
[QUOTE=ponto33;3434561]For the immo off i will open a new topic and will post the original file and the immo off file that i use and still block
http://www.digital-kaos.co.uk/forums/showthread.php/705270-IMMO-OFF-Passat-1-8-20v-ADR-Engine-8d0-907-558-S-0-261-204-956?p=3434564#post3434564
Yes 16 bit
But I don’t know what u will do ?
I nave never mod this maps also not with 1000 injectors
Gesendet von iPhone mit Tapatalk
I run with E100!!
Warm up in E100 needs more 80%+- fuel increasement!
icezero2010
29th November, 2018, 03:07 PM
Than use grundanpassungskonstante and tvub and lambdacorrectionmap or hfm correction
Gesendet von iPhone mit Tapatalk
ponto33
29th November, 2018, 11:36 PM
I tried a while in lambdacorrectionmap, but Kennfeld für Warmlauffaktor stay better
Than use grundanpassungskonstante and tvub and lambdacorrectionmap or hfm correction
Gesendet von iPhone mit Tapatalk
ponto33
11th December, 2018, 03:39 PM
06f00;Startgrundmenge;1x1
06f0e;Startgrundmenge;1x1
0b48a;Kennfeld für Warmlauffaktor;6x8
I change the Startgrundmenge, but the cold start got worse!
Have a way to increase fuel just in cold start?
icezero2010
11th December, 2018, 03:51 PM
I change the Startgrundmenge, but the cold start got worse!
Have a way to increase fuel just in cold start?
here all what u need
ponto33
11th December, 2018, 11:30 PM
here all what u need
Thanks so much!!!!
:)
ponto33
12th December, 2018, 12:21 AM
here all what u need
FKSU.0 / FKSU.1 - 009244 / 00924A ( Abregelung Faktor Kaltstart über Umdrehungszahl )
-------------
KFKSNM.0 / KFKSNM.1 - 00925A / 009280 ( Abregelung Faktor Kaltstart über Drehzahl und
Motortemperatur )
-------------
FKSM.0 / FKSM.1 - 00920E / 009228 ( Kaltstartfaktor )
-------------
FKSWDK.0 00923B ( Kaltstartfaktor abhängig von DK-Öfnung )
ponto33
12th December, 2018, 12:22 AM
here all what u need
it's all 8bits?
and ignition on idle is Zündwinkelkennfeld im LL?
icezero2010
12th December, 2018, 02:35 AM
it's all 8bits?
and ignition on idle is Zündwinkelkennfeld im LL?
yes all 8 bit
ignition you don´t need
ponto33
12th December, 2018, 10:28 PM
here all what u need
my cold start is so good with E100!
But my hot start is not good yet! (the TLST not adjust all, I was decreasing and testing until closed injectors completely and did not starts more, still continued with a bad start
Have a way to increase rpm in hot start? the engine starts "heavy" and start and go to idle RPM, i would like to start go to +- 1.100rpm and go to idle (870rpm)
whats control the idle RPM?
I believe its just it to finalize all!!
:)I was slowing down and testing until I closed my beak completely and did not call anymore, but still continued with a bad match
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.