corsa D 1.3 DTH ecu problem help!

[hamzaman]

hello
i have corsa d 1.3 dth 2007

the original ecu flash is 3333s181 from 1.3DTH and i write another flash is 3137s351 from DTJ by mpss v18
and the car won't start and when i want to write back the original flash mpps says ecu not found .

any solution please ?!
thanks

[gmon16]

Why are you writing different sw file? :itsme:
You need to restore full ori file by bdm now

[MVRH]

Bench only to recover

[hamzaman]

Why are you writing different sw file? :itsme:
You need to restore full ori file by bdm now
i write it by mistake cause i wanted to made egr off
could you please tell me how to restore full ori file
i have clone ktag ?

[gmon16]

post ori file what you read from ecu

[hamzaman]

post ori file what you read from ecu
original file i read it by mpps not ktag
i have 2nd hand ecu 1.3 dtj
if i read full flash from it by ktag and write it to damaged ecu
will work ?

[tarabostesul]

original file i read it by mpps not ktag
i have 2nd hand ecu 1.3 dtj
if i read full flash from it by ktag and write it to damaged ecu
will work ?

nop...............

[hamzaman]

nop...............
so what should i do please ?

[Panathaole]

you read the flash in multi boot mode? or standard MPPS?

If you read as MPPS you get only maps of the flash, if you have use multi boot you have full flash.... easy to recover...

if you have second similar ecu try to read only full flash.......and swap...... i know that ecu in fiat have immo code on flash

opel i think it doesn't, that's the only different of the two versions (fiat Opel), the immo....

[redline974]

Hi, this is full BDM files for your ECU
Upload to ECU and with TECH2 or OPCom make it immo virgin ( PIN 2047 )
After that you can easy adapt it
Use MPPS multitool ( or BDM if it don't work )
Or try to read your files by BDM and send it here for check

[hamzaman]

Hi, this is full BDM files for your ECU
Upload to ECU and with TECH2 or OPCom make it immo virgin ( PIN 2047 )
After that you can easy adapt it
Use MPPS multitool ( or BDM if it don't work )
Or try to read your files by BDM and send it here for check
can i write it with K-tag ?

[redline974]

Yes you can write it with KTAG, but try to read before and send files that you can read, I will check if I can repair your files

[hamzaman]

Yes you can write it with KTAG, but try to read before and send files that you can read, I will check if I can repair your files
ok friend thanks so much

[hamzaman]

Yes you can write it with KTAG, but try to read before and send files that you can read, I will check if I can repair your files
hello
i tried to read the ecu today but ktag can't read
so i program another ecu and the car start but the ecu is for dtj engine not DTH and turbo not working
any solution ?

[redline974]

DTH and DTJ ecu is same Hardware, if they are two MJD6O3 you can use any DTH and DTJ ( but you need full dump MPC / FLASH / EEPROM )

[hamzaman]

DTH and DTJ ecu is same Hardware, if they are two MJD6O3 you can use any DTH and DTJ ( but you need full dump MPC / FLASH / EEPROM )
so i can write the bdm files that you post above i think its for DTh

[redline974]

Yes you can, just have to code immo with pin that i give to you
After that just need to code variant, VIN, and injectors

[TuningInside83]

Have you read the original ECU file? Rewrite in BDM and the car will start

[hamzaman]

DTH and DTJ ecu is same Hardware, if they are two MJD6O3 you can use any DTH and DTJ ( but you need full dump MPC / FLASH / EEPROM )
i writr the file that you sent but they are also for dtj engine :(