Mazda immo box temic immo code

[gazzaull22]

Hi please can anyone give me a the security code from this mazda mx5 immo box

Thanks

[newone]

i think you must read Motorola MC68HC705P3(1F75B) inside

[gazzaull22]

The code can be callculated from the code on the box, Was asking if anyone code do that for me

Thanks

[lion0304]

The code can be callculated from the code on the box, Was asking if anyone code do that for me

Thanks

Give it up for some one else. You don't know what you asking for.

[sleepyrz]

i believe thats a lucas box to pin code conversion you are thinking of???


thats not the lucas box?

[gazzaull22]

Think you have got things wrong here and your not sure what your on about

The code for the immo box is 34 13 42 87 and has been calculated from the 10 digit serial code from the immo box so no need to read eeprom, so i did know what i was asking for and your response help no one.

Thanks

[sleepyrz]

http://sigmabit.eu/media/catalog/mazda_service/mazda_immo_lucas.jpg


i think this is the box you are thinking of

the "lucas" box

i ran your serial on that box that you have anyway through the calculator but it says "no result could be calculated check the data that you entered"


but its a lucas box calculator

i found icc has a "temic immo calculator"


guess thats what you needed?


confirm?

[gazzaull22]

i got the code from 3d group

[sleepyrz]

weird even the ICC calculator says you need to read the eeprom in there


https://www.noimmo.lt/ICC.pdf

page 61....



wonder what they did different

[pizz]

Hello can someone help me with the pin code for my car Ford Ranger 2007 with Mitsubishi immo box 7823942891 thanx in advance

[rafal]

Hello can someone help me with the pin code for my car Ford Ranger 2007 with Mitsubishi immo box 7823942891 thanx in advance

read immobox.................24c01 eeprom

[jodge]

read immobox.................24c01 eeprom

it's mazda Bt50 not Ford and the Mitsu immo using MC68HC805P18 not 24c01... The easy way read from the ECU or somene calcultaing for him. Unless he have an MC68HC805P18 prommer :)

[pizz]

Hi Jodge

Its same with Mazda no difference for sure. Thanks

How can I read the from the ecu? I have VVDI Prog and VVDI2, and other obd2 tools like Lonsdor, X100 Pad2 which can read eeprom but I cannot find the chip to read. I have tried all 8pin but to no avail? I read some posts in this forum where some mates were able to calculate the pin code by immo box number.

any wayout is highly appreciated. I’m stuck for 3 months now.

[jodge]

post picture about the ECU pcb and the sticker too

[pizz]

645851645852645853645855 Hi Jodge these are the pictures. i'm desperate

[jodge]

eeprom is: 95320
my guess:
4th pic check the label of the 8 leg SOIC above the MCU
If it is then desolder (!!!! no clips no bs) the eep

if not check the other 8 legged SOIC or use the default bosch BDM pins

[pizz]

the Clips can damage the ic right? i tried the clip it only shows 00 00 00. thanks. i will do it tomorrow morning

[jodge]

the Clips can damage the ic right? i tried the clip it only shows 00 00 00. thanks. i will do it tomorrow morning


did you checked the label? what was on?

[pizz]

i have just loaded the file from 95320 ic from Ford Ranger/Mazda WE01 ecu. Help me find Pin/Codeword for this ecu pliz.

645907

[jodge]

......24339369.......

[pizz]

Thanks Jorge my next problem is now on programming. I tried putting in and out key 6 timesslso on/off 5 times no change. The car doesn't go into programming mode. Mine doesn't show security light when you insert the key. It only shows when you switch the key
to on position

[jodge]

sorry i never used this manual procedure before. I have prommer for the immobox