View Full Version : how to lift tinny pins from MCU's???
lwood
7th March, 2019, 07:39 PM
i have trouble lifting tinny pins from MCU's.. i am working on a 2019 Subaru Impreza. inside has MB96F6A6 . i need to lift pin64 to read. pin is soo small. i dont know how to lift.
what are you guys using to lift these small pins. ???
clusters
7th March, 2019, 07:45 PM
Cut the trace to it, then solder over when done
lwood
7th March, 2019, 07:55 PM
Cut the trace to it, then solder over when done
yes that what i do. when has a trace. but this pin has ground.
jomberykaso
7th March, 2019, 07:56 PM
In this dash race of pin 64 go to under processor.
601977
You must lift pin. I use a cutter and an iron solder for this kind of job.
Good Luck !
lwood
7th March, 2019, 08:12 PM
In this dash race of pin 64 go to under processor.
601977
You must lift pin. I use a cutter and an iron solder for this kind of job.
Good Luck !
what do you mean you use a cutter?? you cut the pin?
jomberykaso
7th March, 2019, 08:23 PM
I use the cutter to lift the pin while I heat it up with the tin soldering iron.
mikkhh
7th March, 2019, 09:13 PM
or needle and hot air gun, carefuly bend it upwards, use needle as a pry bar between other pins
or use one of those craft cut knife / scalpel.
jomberykaso
8th March, 2019, 12:12 AM
or needle and hot air gun, carefuly bend it upwards, use needle as a pry bar between other pins
or use one of those craft cut knife / scalpel.
I use the same cutter
lwood
8th March, 2019, 12:16 AM
thanks guys.. i am going to use the cutter.
yellowstilo
8th March, 2019, 12:28 PM
a needle works very well, just gently use it as a lever on top of the next pin whilst heating the pin with your soldering iron....
sparkle
8th March, 2019, 12:57 PM
I agree with yellowstilo .
smallest needle you can find , remove solder with braid first , then gently lever up from pin next to it while applying heat from soldering iron tip .
patience & a steady hand and it will work .
DO NOT RUSH THESE JOBS
it will cost you with a f**ked up dash
rubin_miki
8th March, 2019, 01:27 PM
i use needle for acupuncture,just need to twist litle at the end to pull up pin,work very good
lwood
8th March, 2019, 10:57 PM
i use needle for acupuncture,just need to twist litle at the end to pull up pin,work very good
where did you get those needles?
jomberykaso
9th March, 2019, 01:42 AM
where did you get those needles?
Mate...you only need a cutter and soldering iron.
Easy job ....
Cllau
9th March, 2019, 01:50 AM
where did you get those needles?
you can use any needle like sewing needles... 602340:driver:
racin-snake
9th March, 2019, 01:54 AM
where did you get those needles?
TRY here https://www.ebay.co.uk/sch/i.html?_from=R40&_sacat=0&_nkw=acupuncture+needles&_blrs=spell_check
sagie
9th March, 2019, 07:24 AM
large sewing needles is best, grind the bottom end and bend slightly. Bend too much and it breaks
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.