View Full Version : steering assist ibiza 2017 P160900
piotrkokot
8th March, 2019, 02:13 PM
hi how to clear crash this ecu 2Q1909144J, VCDS AND VCP don t work , mcu is sak-tc234lp , maybe only vas or odis onlline, DTC P160900
barth71
8th March, 2019, 09:28 PM
Hi . I had the same problem. I found solution in this tread.
https://forums.ross-tech.com/showthread.php?4988-Skoda-Fabia-MY16-Power-Steering-fault&p=79196&viewfull=1#post79196
You must EPS "restore to factory setting" with VCDS and then calibrate everyhing.
piotrkokot
9th March, 2019, 10:22 AM
don t work this car , login and factory seeting dont worked
robert1232
10th March, 2019, 05:17 PM
you do this with vcds
Perryking
11th March, 2019, 11:33 PM
Any solution? I have same problem with same ecu
yarowsc
7th August, 2019, 11:30 AM
did anyone solve this problem? I have the same thing in Ibiza 2017. , Power Sterring 2Q1909144J.
slick_dick
7th August, 2019, 11:37 AM
I have solution to be used with launch
access login will cost but I can get you code if you need
44. steering assistance (red steering wheel light on dash)
code crash input or similar
enter access permission code, reset factory settings.
no fault, red light still on dash.
disconnect battery for 10-15 mins.
switch car on power steering should be restored!!!
br
slick
yarowsc
7th August, 2019, 11:52 AM
send info PM
redliner
8th August, 2019, 11:21 AM
hi how to clear crash this ecu 2Q1909144J, VCDS AND VCP don t work , mcu is sak-tc234lp , maybe only vas or odis onlline, DTC P160900
VCDS can do it, after uploading readines Clear DTC and disconnect battery for some time.
yarowsc
25th March, 2020, 05:09 PM
I can write yes;
in my case nothing helped, the problem was not solved.
Ibiza 2018year, 2Q1909144J, reflash Odis Online, online parameterization, next reset to factory settings - no changes, sterring does not work, the error is still saved. I also tried to flash VCP, Odis engineered files;
- 2Q1909144J_6030_V001
- 2Q1909144ZU_BOOT_V001
- 2Q1909144ZX_BPLD_V001
- 2Q1909144ZX_BPLD_V002
and nothing. power steering, if it didn't work, it didn't work
some say that Odis Online is the way to go. how ??
I am asking for tips as needed - I will pay.
pinheiro
26th March, 2020, 05:11 PM
Hi friend
I had a similar problem with a seat.
I've tried to clear the fault code with vag-com, but it didn't work.
By texa diagostic I've redefined all adaptations and auto-adaptation (reset factory values)
After turning off the ignition the error desappeared (I don't know how, but...)
Hope this could help you
Best regards
Pinheiro
redefining all adaptations
Boras
17th May, 2020, 07:05 AM
Hi,
have someone pinout for Jtag or Boot for this unit ?
Its One MCU PCB
Regards,
Boras
715242
absetup
29th July, 2020, 10:45 AM
i can do it
Need odis engineering
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.