Tacho universal 2007 Toyota Avensis(1999)

[ballyd1]

Hi, I wonder if any one could help me out on this I have a universal tacho 2007 and have two set of instruction one in English the other German I am trying to correct the mileage on a Toyota avensis 1999 I am using board adapter 93cx6 in the English instruction it says connect to port 1 and clip on chip 93c56 and the German instruction says connect to port 0 I have tried both ports and have joined the crystal ends the mileage does not change on the hand held I choose Toyota>avensis>93c56>attach clip and the mileage just reads 97600 and some times general failure and I have tried this on two Speedo's (both Toyota avensis) and always the same reading there is also a diagnostic display i have tried that but it still does not change the handheld seems ok I have tested it on a vw golf by diagnostic could it be the board that is faulty(93cx6) is there any way to test it or does any one know where I can buy one.Any help will be appreciated.

[drpeter]

Hi, I wonder if any one could help me out on this I have a universal tacho 2007 and have two set of instruction one in English the other German I am trying to correct the mileage on a Toyota avensis 1999 I am using board adapter 93cx6 in the English instruction it says connect to port 1 and clip on chip 93c56 and the German instruction says connect to port 0 I have tried both ports and have joined the crystal ends the mileage does not change on the hand held I choose Toyota>avensis>93c56>attach clip and the mileage just reads 97600 and some times general failure and I have tried this on two Speedo's (both Toyota avensis) and always the same reading there is also a diagnostic display i have tried that but it still does not change the handheld seems ok I have tested it on a vw golf by diagnostic could it be the board that is faulty(93cx6) is there any way to test it or does any one know where I can buy one.Any help will be appreciated.

This car has problems with reading onboard, carefully remove eprom with hot air and read again, problem solved.

Good luck

[einet]

Hi,

the same problem to read on a Renault Megane wiht interface 908, i tray onboard end desoldering de eeprom
but i can?t change the milage!

any a idea.

einet

[drpeter]

Hi,

the same problem to read on a Renault Megane wiht interface 908, i tray onboard end desoldering de eeprom
but i can?t change the milage!

any a idea.

einet

Are you serious? What year Megane? Jeager cluster? Johnson?

[z786]

Hi, I wonder if any one could help me out on this I have a universal tacho 2007 and have two set of instruction one in English the other German I am trying to correct the mileage on a Toyota avensis 1999 I am using board adapter 93cx6 in the English instruction it says connect to port 1 and clip on chip 93c56 and the German instruction says connect to port 0 I have tried both ports and have joined the crystal ends the mileage does not change on the hand held I choose Toyota>avensis>93c56>attach clip and the mileage just reads 97600 and some times general failure and I have tried this on two Speedo's (both Toyota avensis) and always the same reading there is also a diagnostic display i have tried that but it still does not change the handheld seems ok I have tested it on a vw golf by diagnostic could it be the board that is faulty(93cx6) is there any way to test it or does any one know where I can buy one.Any help will be appreciated.

i normally do it using diagnostic :) but removin eeprom is always better on them rather than in-circuit

[drpeter]

i normally do it using diagnostic :) but removin eeprom is always better on them rather than in-circuit

An Avensis can't be done by diagnostic only direct

[einet]

Hello,

...."Are you serious? What year Megane? Jeager cluster? Johnson? "...

Yes, it is a Jeager cluster, but i forget TachoUniversal januar2008 and interface 908 dont let me change the milage or desoldering the eeprom, say syncronise.

einet

[drpeter]

Hello,

...."Are you serious? What year Megane? Jeager cluster? Johnson? "...

Yes, it is a Jeager cluster, but i forget TachoUniversal januar2008 and interface 908 dont let me change the milage or desoldering the eeprom, say syncronise.

einet


You don't need program the eprom but the processor, you have to solder some wires. Don't you have a manual?
What year Megane and cluster?

[obdmaster]

Now now ladies!

[roth18]

Hi everybody,

I have Tacho Universal (China) and I found out that the adapters are very low quality. Once I had to repair one adapter because there was no connection to the pins in and out. The schematics of the adapters are posted on this forum somewhere for download, just search.
Hope it helps.

Roth http://www.kolobok.us/smiles/artists/just_cuz/JC_cheers.gif.

[einet]

Hi,

the manual say to desolder 2 pins on the micro (the 2th and the 5th on the side) and solder the wires to this pins, correct? i make this.
then short the cristal!
then say to disconect the resistence or condensator!?

where pute this cable?

einet

[z786]

An Avensis can't be done by diagnostic only direct

mayb not for you,

i do all avensis clusters b4 2003 diagnostic

hav fun

[drpeter]

mayb not for you,

i do all avensis clusters b4 2003 diagnostic

hav fun
What tool? As for as I know not one Toyota can be done by diagnostic. (Enigma, Diga, DP3, Abritus commander, Data Specialist Plus, ......) All direct, cluster removal. You are a genius

[z786]

What tool? As for as I know not one Toyota can be done by diagnostic. (Enigma, Diga, DP3, Abritus commander, Data Specialist Plus, ......) All direct, cluster removal. You are a genius

If i am correct, you are dr peter from odometer correction forums aswell? you also had you r own forum? you my friend with alot of knowledge must be able 2 do it? i use Tacho Universal , but same adapter can be used for DP3

but i can assure you i do avensis diagnostic, me and a friend (electronic engineer) worked for weeks to make the solution, he has schematics, i dnt hav a clue bout capacitors n resistors and pcbs or else i wud explain 2 u better

[drpeter]

If i am correct, you are dr peter from odometer correction forums aswell? you also had you r own forum? you my friend with alot of knowledge must be able 2 do it? i use Tacho Universal , but same adapter can be used for DP3

but i can assure you i do avensis diagnostic, me and a friend (electronic engineer) worked for weeks to make the solution, he has schematics, i dnt hav a clue bout capacitors n resistors and pcbs or else i wud explain 2 u better

You are right but I only spent time on engineering when necessary. Maybe you want to share your knowledge with us? I am pretty good with capacitors, resistors and integrated circuits, so I am curious.

Thanks for your Info.

Greetz,

Peter

[z786]

i will ask my friend for schematics, i wont post any info without his permission, i dnt break promises.

i can post video if u dnt believ me tho lol

[joesoap112]

SO what was the outcome ....im intrigued!!!!

[z786]

SO what was the outcome ....im intrigued!!!!

im sure u must be lol
im afraid not at the moment sorry

[Air]

I'm still wating too for your diagram