View Full Version : How to access this ECU? Magnetti Marelli IAW 4AVP.GR (Gol G4 2009 Mercosur)
Cordobe1
17th December, 2009, 03:24 PM
Hello everyone,
With that soft / hard are allowed to enter into this ECU?
Not only to diagnose ... but above all to reprogramming .-
Thanks to everyone for the help!
PS: I thank any information that can provide this ECU
hercamp
9th January, 2010, 12:36 AM
hi did u solve youre problem????
I have the same question...
Cordobe1
11th January, 2010, 06:20 PM
hi did u solve youre problem????
I have the same question...
No, I only know that the chip is a ST10 .-
But still can not learn how to enter and reprogram .- :(
juniorlucival
21st January, 2010, 05:01 AM
you enter through, ST10Flasher, an interface that converts RS232 to line k. search in google ST10Flasher 2.02 and understand better.
Cordobe1
21st January, 2010, 07:20 PM
you enter through, ST10Flasher, an interface that converts RS232 to line k. search in google ST10Flasher 2.02 and understand better.
Hi Junior,
Thank you very much for your help!
I have several questions:
1. To read and write the "ST10" I have to remove the ECU from the vehicle?
2. Only RS 232 to K? I can not use a USB to K Line interfaces, such as VAG Com (chine clone)?
3. ST10Flasher is an interface and soft, that I add to my connection with the line K?
Tnks a lot!! :beer:
Cordobe1
21st January, 2010, 08:01 PM
I add the link to the post where they talk of ST10 Flasher
http://www.digital-kaos.co.uk/forums/f68/st10fxx-programmer-54319/
You know that interface is required to use this soft and able to reprogram my ECU?
Cordobe1
22nd January, 2010, 11:26 PM
http://i48.tinypic.com/kbvr6u.jpg
http://i45.tinypic.com/14y8ghz.jpg
Mac Gyver
23rd January, 2010, 06:43 PM
Cordobe1,
attach here the photos of both sides 4AVP board, I do the marking of points where you will make de BOOTMODE.
Cordobe1
24th January, 2010, 08:28 PM
Tnks a lot four de help!! Mc Gyver
:party:
Mac Gyver
25th January, 2010, 02:38 AM
Cordobe1,
I can not attach the photo of 4AVP ecu in the forum.
I have problems with the proxy to access the forum here in my country.
to access the forum I must use the UltraSurf software.
send me your email adress in MP.
Cordobe1
25th January, 2010, 12:50 PM
Cordobe1,
I can not attach the photo of 4AVP ecu in the forum.
I have problems with the proxy to access the forum here in my country.
to access the forum I must use the UltraSurf software.
send me your email adress in MP.
Thank you! :wavey:
already sent my email address
Then I attached the photos to post here so be complete if another user tries the same thing I .-
Cordobe1
26th January, 2010, 07:44 PM
http://i50.tinypic.com/155ninl.jpghttp://www.digital-kaos.co.uk/forums/%5BIMG%5Dhttp://i50.tinypic.com/155ninl.jpg%5B/IMG%5D
stasiekx
10th July, 2010, 10:18 AM
Hi.
I don`t know where i can find any help... I`v got IAW 49F.B4 with Moto ZC439507MFT20 processor (http://stasiek.masternet.pl/MOTO.JPG). How can i make a boot mode? I find smth about 24pin to gnd but is it true?.
powerinyeccion
12th July, 2010, 09:35 PM
esta maquina se puede hacer con el galetto 1250 en Boot mode de fiat para ST10 sin problemas...
nicamarcos
15th July, 2010, 02:55 PM
esta maquina se puede hacer con el galetto 1250 en Boot mode de fiat para ST10 sin problemas...
:D, 49f ecu in boot mode with galletto?
Cordobe1
3rd August, 2010, 11:39 PM
esta maquina se puede hacer con el galetto 1250 en Boot mode de fiat para ST10 sin problemas...
Hola estas seguro??
Gracias!
jarripote
8th October, 2012, 09:14 PM
Hello, anyone confirm this information? thanks
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.