visa 1.83

[ezenigbo]

i bought euroscan for over 2years now but cannot use it becuse i cannot put the software well to work.the first pc i used is pentium 2,the pc can communicate with my euroscan when i powered it on desk.it shows CONNECT ECU READER AND CHECK POWER, then it opens the other screen,but now my pentium 2 pc is dead,i got another pc,pentium 4[intel],i configured window 98 and xp [partitioned],when i used the software,by powering on desk also,it will display as above but will not open the next page,meaning no communication from pc to the hardware.what is the problem?does it means that it must be oldest model pc before euroscan can work?

[Qwarz]

I have Penium III 500Mhz and Visa works perfectly under MS-DOS mode.

[zogldi]

C:/VISA go to dbcodici right click mouse> properties> advanced>spec. MS-DOS mode you need,click on it.C must be FAT32 and you must have two serial port (no virtual only real serial).
B.R.

[ezenigbo]

i have set vstart and dbcodici to ms- mode.what is fat 32 and how do i check it?can i specify a new ms-mode or use current ms-dos configuration?please help.my pc has double com port and i plug in the hardware there.how do i know whether the com port is serial or virtual?

[ezenigbo]

see my system property;MEMORY:248.0 mb SYSTEM RESOURCES:92% free FILE SYSTEM:32-bits VIRTUAL MEMORY:32-bits DISSK COMPRESSION:not installed PC CARD[PCMIA]:no pc card suckets are installed .YOUR SYSTEM IS CONFIGURED FOR OPTIMAL PERFORMANCE, can this help to solve my problem?

[AEN]

ezenigbo

Do you use Win98?
It is impossible to organize correct DOS-session for Uniscan under Win2K and higher...

[zogldi]

i have set vstart and dbcodici to ms- mode.what is fat 32 and how do i check it?can i specify a new ms-mode or use current ms-dos configuration?please help.my pc has double com port and i plug in the hardware there.how do i know whether the com port is serial or virtual?
Yes you need new MS DOS mode and WIN98 OS.

[ezenigbo]

yes i used ms dos mode window 98 SE.i have also tried euroscan 1.82 paqckage.i installed the software in window 98 still thesame.although i have never connect to car.but as far as i powered it on desk ,i supposed to get communication.should i abandon the pentium 4?

[AEN]

Pentium 4 should work. Do you use real COM ports?

[ezenigbo]

my pc has 2 comport and i connected them to the hardware wires.which one is serial port?

[Qwarz]

Serial port = 9-pin connector

[ezenigbo]

my com ports are 9 pins each,as far as the two wires from my euroscan hardware entered.this is the information from my system;SYSTEM;microsoft windows 98 second edition 4.10.2222a REGISTER TO;USER;50578-335-0015645-03399 COMPUTER;genuinltel x86 family 15 model 1 stepping 2 248.0md ram

[BeianM]

I have previously discussed this on another forum.
Uniscan Euroscan Visa 1.83 fully working on UK cars - OBD-Codes.com (http://www.obd-codes.com/forums/viewtopic.php?f=10&t=1583)
Take a look & report back here. I must admit that I neve got it to work on the couple of cars I tried it on, even with proven software. Remember to check your comm ports are not sharing their interrupts. Check in properties that visa is set to run from dos. Best to boot to dos, I set up a boot manager that gave me the opportunity to boot to dos or windows.

[baasharm]

Can Uniscan be used to reprogram the remote key? Or is that exclusively done with the examiner?

[mecadriano]

ingles ver?ao ?????1.83

[BeianM]

ingles ver?ao ?????1.83

change Messcode.RUS to Blank.RUS you must also rename the .RUS files in the DIAG_EXE directory

I have had limited success with it. Some good advise here => Uniscan Euroscan Visa 1.83 fully working on UK cars - OBD-Codes.com (http://www.obd-codes.com/forums/viewtopic.php?f=10&t=1583)

[manocao]

Uniscan or Euroscan's VISA 1.83 by manocao for u all (http://www.digital-kaos.co.uk/forums/f104/uniscan-euroscans-visa-1-83-manocao-u-all-84463)

[jo?o antonio]

Hi guys,

There were UNISCAN-VISA 1.83 install procedure in the "old Garage" forum.

( requeriments , procedure, guide , database install ) all , all .

Can somebody re-upload it here.

Regards

[uncle_sem]

change Messcode.RUS to Blank.RUS you must also rename the .RUS files in the DIAG_EXE directory

I have had limited success with it. Some good advise here => Uniscan Euroscan Visa 1.83 fully working on UK cars - OBD-Codes.com (http://www.obd-codes.com/forums/viewtopic.php?f=10&t=1583)
no need to rename/ just run not the vstart, but dbcodici. well, not sure about the correct exe file, will look tomorrow at work :) but russian uniscan is working in english perfectly with the same adapter... has tried few times when translation to russian is unreadable...

[uncle_sem]

just checked - run vstart.exe for russian version, run dbcodici.exe for english. maybe it depends on firmware version

[jo?o antonio]

H? folks,

The V2 version of Uniscan-Visa 1.83 ( by Manocao ) is already added to the new database ECM ?

Thanks.