PDA

View Full Version : Land Rover Discovery 3 Dash problem


McDowell
6th May, 2019, 05:47 PM
Hello mates,

I have swap a discovery doesnīt recognise chassis information, can someone please write me right inofrmation on eeprom?

617663617664

I am attaching ORI and DONOR just in case ori is corrupted. They are both same reference dash.

VIN SALLAA187A423988
280000KM

Thanks in advance :)
jomberykaso
7th May, 2019, 05:38 AM
original mileage is 287.356 kms and here is your original file fixed.

Good Luck!
McDowell
7th May, 2019, 07:24 AM
original mileage is 287.356 kms and here is your original file fixed.

Good Luck!

Many thanks I will try and report :)
McDowell
13th May, 2019, 03:35 PM
Many thanks I will try and report :)

iIt did not work, still saying he VIN number does not match, any ideas?

Thanks a lot
jomberykaso
13th May, 2019, 04:11 PM
I put the vin number in the correct place . You can compare them and verify if I put the correct one
McDowell
13th May, 2019, 04:19 PM
I put the vin number in the correct place . You can compare them and verify if I put the correct one

I know, itīs strange. I have written your eeprom modification to both ori and donor.

The original one which is flickering on and off says the VIN is correct, while the other one still having an old number, I know about 35080 delete and write, maybe I have had a mistake. Iīm gonna read donor 35080 anc ompare with yours and see if it still the same.

Thanks a lot
McDowell
14th May, 2019, 08:19 AM
Is it possible the IMMO data is not in 35080? because miles change but not the VIN number... :(
PremierD
14th May, 2019, 08:31 AM
Immo data is in the Micro mate .. you need to swap both ...
McDowell
14th May, 2019, 08:44 AM
Immo data is in the Micro mate .. you need to swap both ...

Ok but there is an issue, micro is broken....its flickering on and off the dash :( and if I warm it up works fine.

Any pinout to read it in the board?
PremierD
14th May, 2019, 08:50 AM
No immo data no go mate ... so you are screwed.. sorry
McDowell
14th May, 2019, 09:21 AM
No immo data no go mate ... so you are screwed.. sorry

Bbut is there any chance to read it and write? because is working when warm, so i could read it warm and it will be fine.
levisdj
14th May, 2019, 11:29 AM
Then keep it hot while reading ....
McDowell
14th May, 2019, 12:00 PM
Then keep it hot while reading ....

Do you know how to read it? sorry for so many questions :s
tech_cz
14th May, 2019, 12:07 PM
it depends on what kind of MCU is there.
You did not write anything about it nor post picture of it.

WBR, Marek
McDowell
14th May, 2019, 12:11 PM
it depends on what kind of MCU is there.
You did not write anything about it nor post picture of it.

WBR, Marek

Thanks for your reply. See attached itīs 64f2638f20

619732

Cheers :)
PremierD
14th May, 2019, 01:47 PM
http://www.eevblog.com/forum/microcontrollers/programming-h8s2638/
Aislingob
15th September, 2020, 08:06 PM
Does anybody know how to repair these type of dashboards without swapping and chips and tmrepairing existing unit?
Safety
16th September, 2020, 07:39 PM
Old model diagnostic 1.18 version change VIN by OBD
Aislingob
1st July, 2021, 09:35 AM
thanks for your help Safety, which tool has software 1.18 ??
Mvt
23rd February, 2023, 06:24 PM
hi guys
same issue looking how to swap cluster original cluster mcu damaged eeproms 35080 vp swapped vehicle does not start now km reads correct
thank you