Need help for read mask 0D46J from EWS3

[trunggt2007]

Hello, i want to program key for a BMW e46. I used my CGPro 9S12 for reading chip 0D46J on EWS3. Because there is not a arrow on my adaptor, so i identified arrow as the photo. My procedure as following:
Align pit on chip with a arrow on adapter ( arrow as photo)
Choose immobilizer/BMW/ EWS3 0D46J
Click "Read" button
But it uassually show message "Power on operation failed" as photo or show all "0" or all "F".
Can anybody tell me why i can not read this chip, what did i do not correctly when read the chip?
I can not find any guide read this chip with my CGPro 9S12 on internet. Thanks

[lion0304]

Buy less than 30$ the AK90, it's the best tool for EWS.

[Manta1600]

pins need very very good cleaning with sharp tool

then need very hard pressure over the socket

[trunggt2007]

pins need very very good cleaning with sharp tool

then need very hard pressure over the socket
Thank you much. Have you ever red chips EWS by CGPro 9S12 ? i am afraid that i identified direction of adaptor not correctly so i can not read this chip. How to can identify direction of adaptor correctly?

[lion0304]

With adapter, usual you cannot put the wrong way. One corner is diffrent than others.

Use thin sand paper and clean the pins. After clean again with acetone.

[Manta1600]

Thank you much. Have you ever red chips EWS by CGPro 9S12 ? i am afraid that i identified direction of adaptor not correctly so i can not read this chip. How to can identify direction of adaptor correctly?

I'm reading them with AK90


but is the same situation - need very good cleaning and hard pressure


please upload picture inside the PCB and show where you put the arrow

[trunggt2007]

With adapter, usual you cannot put the wrong way. One corner is diffrent than others.

Use thin sand paper and clean the pins. After clean again with acetone.
Thank you for your valuable information.

[trunggt2007]

I'm reading them with AK90


but is the same situation - need very good cleaning and hard pressure


please upload picture inside the PCB and show where you put the arrow
Thank you much. i do not have real EWS3 here for taking photo, but i aligned dot on chip and arrow on adaptor as these photos. i have red cas2 and cas3 already by my CGpro 9S12. But it is the first time i use adaptor for reading chip 0D46J on EWS3. i pressed adaptor on chip but i see it seem loose.625716625717625718

[SvanKem]

EWS editor 3.2.0, it's the best tool for EWS 3 ,0D46J .

[trunggt2007]

EWS editor 3.2.0, it's the best tool for EWS 3 ,0D46J .
Thanks, but i can not read chip successfully with my CGPro 9S12.

[Manta1600]

Aligen is OK

If you still cant read - change the tool

[jimmy060]

Thank you much. Have you ever red chips EWS by CGPro 9S12 ? i am afraid that i identified direction of adaptor not correctly so i can not read this chip. How to can identify direction of adaptor correctly?

Never use that CGPro to read with it. That tool leave a bad taste in your life. Not reading...but damaging.

[PixelsFixed]

I've never successfully read EWS with cgpro - I gave up trying. Buy AK90.

[tomvleeuwen]

i pressed adaptor on chip but i see it seem loose.

I always keep pressing the adapter down with force while reading, it's the only way that works for me. (AK90, don't know if CGPro is capable at all)

[musti418]

hi, i am reading with vvdi prog adapter without any cleaning sandpaper needed. safe and trouble-free.

[Oktawian]

Carprog can read it via ews plug with no worries.

[castin]

Xprog read good too by kline and one boot pin.