View Full Version : 2014 Renault Master all keys lost
cqae
26th July, 2019, 05:21 AM
Has anyone done any all keys lost on a 2014 Renault master before? If so I was hoping for a heads up on how to do it, what to read etc?
nazz2
26th July, 2019, 10:56 AM
Is it X62 chassis? what tools (key programmer)do you have? true code, and ad100 is your best mate. also check Tmpro module 44 & 57.
cqae
12th August, 2019, 09:09 AM
Thanks Nazz2, I am not sure of the Chassis, I can't get to the car just at the moment. I have zedfull, avdi, vvdi prog & tango. I was hoping these might cover it. Zedfull seemed to work, but I am not sure I had the right transponder. can anyone confirm the transponder type? I tried a blank ID46, but think it may of needed precoding?
TukoSalamanca2
12th August, 2019, 11:38 AM
Fvdi can do AKL Renault Master X62 chassis?
qwertyuiop12
12th August, 2019, 12:45 PM
Renault Master
key 2 button PCF7947
immo in BCM
didi_du_93000
18th December, 2019, 09:48 PM
Hello, i have programed remote key pcf7947 from china, immo is ok and car start. but remote don't work. Original remote working great and not the chines remote.
Never have probleme with this remote on other cars (clio, kangoo, modus...)
I have also read all values from ori 7947 and write back on the chines remote, same result.
I have learn keys by renautl ecu tool.
Matronix
18th December, 2019, 09:54 PM
still think it is remote... sure nr of buttons is ok? Just did a 3 key session on a Master 2012 and it was 3 button... If you check signal with frequency tester is testing ok 433mhz? What did you use for programming. My Autel IMI608 failed, think AVDI could have done it but I did it using Jifeline online programming service.
Catalizator
18th December, 2019, 10:25 PM
[QUOTE = didi_du_93000; 3748314] Здравствуйте, я запрограммировал удаленный ключ pcf7947 из Китая, immo в порядке и машина запускается. но пульт не работает. Оригинальный пульт работает отлично, а не скулы пульт.
У меня никогда не было проблем с этим пультом на других автомобилях (clio, kangoo, modus ...).
Я также прочитал все значения из ori 7947 и записал обратно на пульт дистанционного управления, тот же результат.
Я изучил ключи с помощью инструмента renautl ecu. [/ QUOTE]
poor preparation of transponder from china. a frequent case ..... use the original or recode pcf as needed precoding
didi_du_93000
18th December, 2019, 10:45 PM
But if i write same value than original remote who is working. Why the remote from china don't work?
Catalizator
18th December, 2019, 11:26 PM
cheap Chinese fake. whoever works with keys knows that not all sellers have Chinese keys. program another key if this one refuses to work
Catalizator
18th December, 2019, 11:27 PM
[QUOTE = didi_du_93000; 3748351] Но если я напишу то же значение, что и оригинальный удаленный, который работает. Почему пульт из китая не работает? [/ QUOTE]
give a photo of the masterpiece
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.