View Full Version : Mazda BHN9-57K30A help
PSAcars
26th July, 2019, 01:27 PM
Hello to all. I have Mazda US BHN9-57K30A , the problem is that inside there is no XC2361B-56 , but XC2365A-104F. Can some one clear this ecu?
PSAcars
27th July, 2019, 06:29 AM
Hello to all. Car is from Canada not US. Here is bin file, please clear it.
lwood
27th July, 2019, 07:24 PM
Hello to all. Car is from Canada not US. Here is bin file, please clear it.
this should work.
PSAcars
28th July, 2019, 09:11 PM
Hello to all. Sorry Iwood but after your file I have U3000 control module, but I dont have crsah event stored.
PSAcars
29th July, 2019, 04:45 PM
Hello to all. What to check on board if file is good but I still have U 3000?
lwood
29th July, 2019, 10:33 PM
did you clear codes with scan tool?
you need to clear codes .
PSAcars
30th July, 2019, 04:09 AM
Hello to all. I do this on bentch with carprog I do diag and with Upa I read and write the board.
robert1232
30th July, 2019, 06:49 AM
try this
in your file is crash
thanks
pass
raport
PSAcars
30th July, 2019, 08:37 AM
Hello to all. To Robert1232 I have this after power up, clear, power down 20s, power up.
U3000 - Control module
U0834 - Unknown error
U012C - Unknown error
B1F40 - Unknown error
ElderDM
30th July, 2019, 11:58 AM
Hi.
Test and report.
Regards.
PSAcars
30th July, 2019, 12:09 PM
Hello to all. To ElderDM
key on, read, erase, key off20s, key on, read
B03F3 - Unknown error
U3000 - Control module
B0160 - Ambient Air Temperature Sensor Circuit
B1F40 - Unknown error
superjet
30th July, 2019, 12:40 PM
Whcih error with your ori file?
PSAcars
30th July, 2019, 01:13 PM
Hello to all. This are fault codes with crash file, like how it came to me.
B0010 - Passenger frontal stage 1 - deployment control
B1214 - Passenger safety belt reatractor pretensioner deployment control
B0466 - Unknown error
B0467 - Unknown error
B0468 - Unknown error
B0469 - Unknown error
B0011 - Passenger frontal stage 2 - deployment control
B0048 - Unknown error
U0155 - Lost communication with instrument cluster control module
U07D5 - Unknown error
B03F3 - Unknown error
U3000 - Control module
B04CB - Unknown error
B04AC - Unknown error
B04CA - Unknown error
B04AD - Unknown error
B0094 - CPS childseat detection error
B0589 - Unknown error
B1193 - Crash event stored
B0160 - Ambient Air Temperature Sensor Circuit
superjet
30th July, 2019, 01:19 PM
Replace the bad parts clear errors then read again and upload the new file.
PSAcars
30th July, 2019, 01:22 PM
What bad parts, on pcb or in car ????
superjet
30th July, 2019, 01:27 PM
Airbags and seat belts on the car,or use a resistor instead.
PSAcars
30th July, 2019, 01:32 PM
I can read this ecu only by board connection by UPA-S, is it going to read in car with ecu connected?
lwood
30th July, 2019, 05:46 PM
you broke module . by using CP and UPA's. to read Infineon. . module no good anymore. if you dont believe me. write original dump back . you will get B3000.
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.