Both needles not working properly after editing eeprom

[euasmdas121231]

Guys, what could be the reason for both - speedometer and tachometer needles to not work properly after removing them and editing the eeprom?

They both dont go any futher than zero mark when speedometer is dissasembled (they rest at 0 and don't go lower than that so I think they are installed properly)

Also when I turn the ignition on, they go from ZERO to maximum.

But when I drive the vehicle, speedo is showing double to triple the real speed (starts from zero, but at 30km/h it shows something like 80kmh etc)
And also the tacho needle at the idle shows approximately 3000rpm instead of 1000rpm.

Are both motors broken or could that be because of an eeprom ?


Speedo is from Suzuki DL650 (same as Suzuki DL1000), year 2007-2010

[kiszka]

Guys, what could be the reason for both - speedometer and tachometer needles to not work properly after removing them and editing the eeprom?

They both dont go any futher than zero mark when speedometer is dissasembled (they rest at 0 and don't go lower than that so I think they are installed properly)

Also when I turn the ignition on, they go from ZERO to maximum.

But when I drive the vehicle, speedo is showing double to triple the real speed (starts from zero, but at 30km/h it shows something like 80kmh etc)
And also the tacho needle at the idle shows approximately 3000rpm instead of 1000rpm.

Are both motors broken or could that be because of an eeprom ?


Speedo is from Suzuki DL650 (same as Suzuki DL1000), year 2007-2010

when the original eeprom saves, the fault disappears

[euasmdas121231]

I am not sure, I haven't tried it yet.
But is it possible that tachometer doesn't show proper RPM's because of an eeprom? I think eeprom doesn't have anything to do with the tachometer? Or I am wrong?
Should I try to reset it back to old eeprom code?

[kiszka]

I am not sure, I haven't tried it yet.
But is it possible that tachometer doesn't show proper RPM's because of an eeprom? I think eeprom doesn't have anything to do with the tachometer? Or I am wrong?
Should I try to reset it back to old eeprom code?

in eeprom is the whole configuration of the meter

[Tefocm]

The EEPROM has everything to do with both needles. You did everything right except for the software changes.

[jomberykaso]

I am not sure, I haven't tried it yet.
But is it possible that tachometer doesn't show proper RPM's because of an eeprom? I think eeprom doesn't have anything to do with the tachometer? Or I am wrong?
Should I try to reset it back to old eeprom code?


Post original file here and all information about car:

Brand:
Model:
Year:
Original mileage:
New mileage you need:

[euasmdas121231]

643351it's a motorcycle

Brand: Suzuki
Model: DL650 V-Strom
Year: 2008
Original mileage: 75 530 km
New mileage you need: 37 329 km643351

I attached the original file and the one that I made.

[kiszka]

it's a motorcycle

Brand: Suzuki
Model: DL650 V-Strom
Year: 2008
Original mileage: 75 530 km
New mileage you need: 37 329 km

I attached the original file and the one that I made.
unfortunately you killed the meter with poor eeprom reading
you need to look for new eeprom content

[jomberykaso]

..............................

[kiszka]

I think your reading is not good .....report..........


Good Luck.

eeprom configuration is corrupted,
none of your work will not work correctly

[jomberykaso]

kiszka (https://www.digital-kaos.co.uk/forums/member.php/69387-kiszka),You are right....he needs to buy a good programmer

[euasmdas121231]

My code was a lot different than yours. I hope that was the cause of the problem.
Tomorrow I will try if it works and then let you know.

Thank you for your help guys!

And what programmer should I use? Is MiniPro TL866CS that bad ?

[jomberykaso]

buy upa 1.3 clone, it's cheaper and better than yours.

[kiszka]

kiszka (https://www.digital-kaos.co.uk/forums/member.php/69387-kiszka),You are right....he needs to buy a good programmer

no, he must learn to use what he has
I'll make him an eeprom with your counting because I'm lazy
and it should work, I think

[euasmdas121231]

Thank you guys, problem was solved!
Jomberykaso helped me out with the eeprom!
Thank you Jomberykaso and Kiszka !

[jomberykaso]

Thank you guys, problem was solved!
Jomberykaso helped me out with the eeprom!
Thank you Jomberykaso and Kiszka !

643420
..............................