problem reading alfa 159 2.0 mjet by obd

[alfanacleto]

hi,friends today i tried to read alfa 159 2.0 mjet edc16c39 by obd,but i cant do it,ksuite said error during data transfer,in the past i can read two car like this with this kess( 4.036 clone) without problem,but in the last 15 days got the same problem with 2 car like this,someone has this problem before? its rare because i read this model and type of ecu many times before,but now seems i cant read it, kess problem? thanks in advance

[alfanacleto]

Nobody got this problem before?

[a500tut]

You can try do this with galletto and mpps or with kess 5.017
You must take out ECU and remap at table.

[alfanacleto]

Its possible only write??

[gas43]

https://www.digital-kaos.co.uk/forums/showthread.php/470321-Kess-V2-Harware-Rework-FREE-SOLUTION!/page67

[alfanacleto]

https://www.digital-kaos.co.uk/forums/showthread.php/470321-Kess-V2-Harware-Rework-FREE-SOLUTION!/page67
Thanks but i cant gind any solution in this threat

[khaos87]

If the laptop which is installed Kess goes online it's possible to damage the memory on the Kess and have issues, check protocols in the Kess, or try to reinstall it..
Regards!

[alfanacleto]

If the laptop which is installed Kess goes online it's possible to damage the memory on the Kess and have issues, check protocols in the Kess, or try to reinstall it..
Regards!
This kees has been onlune in the past but i reinstall it and then work on bmw edc16c35 protocols are ok,i can select car make,car model,but with this 2 159 got id but error when i tried to read,

[zoro1]

On Alfa edc16c39 my tools-galleto ,mpps v18 and kess say-2 hour read!And i made it on table BDM with galleto -gob for 30 minutes with opening the ecu and reading /writing.All the jo0b was to get ECU out of the car .Car 2,4 jtdm 2004 year

[AVDigitale]

after 2008 year fiat put new processors in edc16 what is very hard to read through OBD ,so the best way is BDM

[alfanacleto]

On Alfa edc16c39 my tools-galleto ,mpps v18 and kess say-2 hour read!And i made it on table BDM with galleto -gob for 30 minutes with opening the ecu and reading /writing.All the jo0b was to get ECU out of the car .Car 2,4 jtdm 2004 year
Edc16c39 of 1.9 and 2.4 jtd its easy read and write with cheap mpps v13 clon,edc16c39 of 2.0 jtd its diferent history

[alfanacleto]

after 2008 year fiat put new processors in edc16 what is very hard to read through OBD ,so the best way is BDM
I know,but sometimes i can read it easy with kess( same model car,same year) i dont know why this 2 times i cant,ill try again with 5.017,thanks

[lsdlsd88]

problem is noise on can lines. you can try to set minimum speed in kess options. if still doesn't work you can connect by pinout without needing to open. write by obd.

[alfanacleto]

problem is noise on can lines. you can try to set minimum speed in kess options. if still doesn't work you can connect by pinout without needing to open. write by obd.
Pin out without open??
Have you got a picture of the pin out??
Can i write safe by obd if a take vittual read file?

[ziomski]

You can easly find it on google, type edc16c39 pinout. You need only check ECU sw. wersion, then you can found oryginał file, and wirite it by one, opening ECU is not nessesery

[alfanacleto]

You can easly find it on google, type edc16c39 pinout. You need only check ECU sw. wersion, then you can found oryginał file, and wirite it by one, opening ECU is not nessesery
Ok,but you know if i write by obd virtual.read?