Add key cas4 f06 bmw level 5 message.

[gttuning]

Hi guys add it key to F06 edc17cp45 CAS4
Ingnition will come on but not start the car..
When i take abrites and go to CAS keys there is message BMW level 5 not supported..
Keyless wont work but when put key to steering column it recognize the key messages on screen start the engine...
First key i programed i put wrong ISN by mistake..
Could this effect ECU or CAS....
I read cas4 by smoke ...eeprom verified ok twice and flash aswell..
Ecu read by flex ...

Sent from my SM-G955F using Tapatalk

[PixelsFixed]

Bad key most likely. Try another one. I did a FEM that did that with an oem renewed key. Only worked at the emergency point. New chinese key worked perfectly.

[gttuning]

We tryed two keys..
One from 3d..and one possible Chinese..
It was lost keys..and car still would not start..
Keys was added by dump....
Swith ignition on only when key is at steering column...
Message on dash start engin now..
But still not starting..


Sent from my SM-G955F using Tapatalk

[PixelsFixed]

Definitely CAS4? No ISN required? Cranking?

[Weasel3]

Year of production?

[gttuning]

Definitely CAS4? No ISN required? Cranking?Hi.
This is lost keys job..
F06 2013 640D
CAS4 mask 5M48H and EDC17cp45...
Have ISN from ecu...
Load cas4 dump to abrites key tool.. put in ISN and program key...
Go to car register the key at the steering column and have message that i can start engine..
So engine cracking but not starting..
No DTC in any modules..
And keyless not working..only ignition on when put key next to steering column..
Remote unlock and lock car..


Sent from my SM-G955F using Tapatalk

[gttuning]

Year of production?F06 640D 2013

Sent from my SM-G955F using Tapatalk

[Weasel3]

F06 640D 2013

Sent from my SM-G955F using Tapatalk

Yes this is CAS4+ mask 5M48H.
It was originally a OBD, or bench job?

[gttuning]

Yes this is CAS4+ mask 5M48H.
It was originally a OBD, or bench job?No working key ...so bench job..
Read CAS dump with smok...
Verify eep..ok.. and flash verify ok..
I read 4 times to make sure it read good..
So files from CAS should be fine..
Else smoke done something when reading..
But today had F10 2013 520 and read CAS4 ok add key and all ok car starts..so smok is ok..

Sent from my SM-G955F using Tapatalk

[bearheroes]

Common problem with avdi...keys are ok...

[gttuning]

Common problem with avdi...keys are ok...Yesturday had f10 for key..
Same mask of mcu and read with smok..
Add key with dump tool..
And all works..

On the F06 we add two diffrent keys..
First key add with avdi..
Second key i think with vvdi not sure as i send files to different locksmith guy..and he dosent use avdi..i think vvdi..
But same problem ..
Car cranks only when key next to steering column..

Sent from my SM-G955F using Tapatalk

[gttuning]

Lost key is found car still not start..so have to see what is wrong..
Thanks so far..[emoji106]

Sent from my SM-G955F using Tapatalk

[bearheroes]

Avdi destroyed encryption...

[gttuning]

Avdi destroyed encryption...How would it...
When i didn't write back to CAS..?
I only read CAS with smok and load file to avdi and key is ready to start
Else smok done something when unsecuring and reading...

Sent from my SM-G955F using Tapatalk

[TERMINATOR1000]

How would it...
When i didn't write back to CAS..?
I only read CAS with smok and load file to avdi and key is ready to start
Else smok done something when unsecuring and reading...

Sent from my SM-G955F using Tapatalk

only read = zero risk !

[gttuning]

only read = zero risk !Yes thats what i dont get...
Will have car in garage this week..


Sent from my SM-G955F using Tapatalk

[rola1971]

only read = zero risk !

smok not only read,it unlock mcu.vvdi prog only read backup after unlock
but smok start fron unlock after read
may be it problem

[gttuning]

so guys i test the CAS unit today on different car f10 with same cas4 number..
i read the f10 CAS and write buck up to the CAS from f06 (this is the CAS that wont work with key that we add to F06)
so upload the f10 data and plug in the CAS unit to f10 and car works as normal..so CAS4 UNIT IS OK..
I must have problem with files from F06 ..:(
i will start new thread so hope someone have some buckup from CAS4 f06 with ecu isn number..

[TERMINATOR1000]

smok not only read,it unlock mcu.vvdi prog only read backup after unlock
but smok start fron unlock after read
may be it problem

OK thanks , i have only vvdi prog !