BMW E60 3.0d help dpf off edc16cp35

[misiujakub]

Hi,

I need DPF off BMW E60 3.0d edc 16cp35 0281013500 bmw 7803369 flash BDM this ecu.

DPF broken and message error p4020, p4d03, p41ba.

Thanks for all help:tears_of_joy::tears_of_joy:

[Mooti]

Test And Report
Pass PM

[Mooti]

clear the message box

[misiujakub]

Cleared sorry

[momogsm]

HI

DPF OFF, CHECKSUM CORRECTED

PASS IN PM

REPORT BACK

THANKS

[misiujakub]

Not working correct

[chafik4051]

try and report,
pass in pm.

[momogsm]

Not working correct
HI

DO YOU TRY MY FILE ? WHAT PROBLEM DO YOU HAVE ?

REPORT BACK

THANKS

[misiujakub]

ECU message error p4020, p4d03, p41ba in ride 50 km, all sensor is Connect .

[misiujakub]

I off dpf in ADS, this file ok ?

[Lambda1]

With ori file:
- Delete adaptions,
- Delete error memory,

Flash dpf off file. Run.

[misiujakub]

With ori file:
- Delete adaptions,
- Delete error memory,

Flash dpf off file. Run.

BMW not working this flash. :(
does not start the engine.

[Mooti]

Convert checksums, so don't start

[misiujakub]

CHK ok Galletto in program correct CHK, ecu send error P4A63 and 3E90

[Lambda1]

file from your car or another file? Its ews tampering...
Did you press starter without ecu, so rolling code changed?

[misiujakub]

A file from this car has run out of battery. The ECU does not start after charging and connecting. I have uploaded the first file but it still doesn't burn. EWS probably changed the code

[Lambda1]

Yes rolling code I think is changed.
You need good power supply... good battery and do ews sync, after.
But first programming (if you read bdm, write bdm)!

[misiujakub]

I'm sorry I didn't write BDM, I will improve. The car is connected to the 70A Flash Fronius power supply. I select in INPA E60> Engine DDE6.0> Activation> CAS start restore> Back> Back> Back, turn off the power, disconnect EOBD, remove the key, close the car. I open the car, put the key in, spins the moment and doesn't start.

[naskochipa]

Hi,

I need DPF off BMW E60 3.0d edc 16cp35 0281013500 bmw 7803369 flash BDM this ecu.

DPF broken and message error p4020, p4d03, p41ba.

Thanks for all help:tears_of_joy::tears_of_joy:

Thanks and Reputation

Pass-PM

Test and Report

Upload the original car file delete all errors and make dff and differential pressure sensor a success

[Lambda1]

Lol so you read via bdm but write obd :O?
Well done. Should be clear to know you shouldnt write a bdm flash file via obd or visa versa.

Seperate ecu, write in bdm and hope it will came up alive again.
If dont, hope you got backup ... get spare ecu and write backup, after write mod file for flash.
Put in car... sync

[misiujakub]

I always reads and programs BDM V54, EOBD I wrote about CAS DD synchronization. You misunderstood me. The driver is alive. Full car diagnostics is only an error with 4A63

[Lambda1]

Read CAS Modul ISN and compare to ecu isn. Reset Rolling code, allign and should run. If dont you mess something up or write wrong data.

[misiujakub]

Read CAS Modul ISN and compare to ecu isn. Reset Rolling code, allign and should run. If dont you mess something up or write wrong data.
ECU don't have errors in synchronization.

CAS have 1 error A0B4, if I active CAS ecu cars
VIN: unknow
Write start value : i.o
Reset CAS : i.o
Prepare DME : i.o

Start-value prog. ok reset successful.

Engine don't start.

Data Ecu write to BDM all first read.

[misiujakub]

In ECU don't have error, but in Measurement ,, synchronization no ok. '' , WHY ? CAS error A0B4 but starter working.