Cloning edc17c64 problem!

[alfons37]

I have try cloning edc17c64 vw craftyer 2016 but not work, anyone can help me with correct files so car start https://mhhauto.com/images/smilies/smile.gif Thanks



I have read on bench.

[Stig33]

Try this and please send report....

If I help, please use THX+REP button.

It's from transferred from ORG to DONOR.

[alfons37]

I try your files and car crank no message on cluster but no start only crank and glow lamp flash, check dtc it say p0606

[Stig33]

If you have ODIS-E, or VCP try flashing with *.frf

[alfons37]

I have try flashing before with prog but not work

[Stig33]

Here you have *.FRF file....

[Stig33]

The OLD ECU is "ORG" and the NEW ECU is the "DONOR" ?

[alfons37]

Yes it is correct thanks :)

[alfons37]

FRF file is it for downgrade software?

[ecuprogramer]

hello everyone i can do cloning to work and start the car, do i need help ???

[ricked]

your files cloned:

[alfons37]

Thanks ricked :)

But maybe i do misstake when i reading ecus.

Now i open my org ecu and read with prog, first time i read only with klu, scary to open org ecu :), i have different read with prog org bench on eeprom, but flash is exactly same read. Maybe is wring :)
I attachement dump from prog org / donor ecu.

[ecuprogramer]

alfons37 (https://www.digital-kaos.co.uk/forums/member.php/76669-alfons37)

hi my freind help you for good clone solution......

rep + thnx button

org ecu all data:

[ECU]
VIN="WV1ZZZ2EZG6063947"
IMMO ID="VWZCZ000000000"
CS="19 27 8D FE 21 D6 00"
MAC="50 B4 5C D5"
Config="00 00 00"
PIN="30850"
Immo Type="IMMO 4"
Immo Status="Learned"

donor ecu all data:

[ECU]
VIN="WV1ZZZ2EZG6043913"
IMMO ID="VWXDZ0P1018270"
CS="0A A9 41 00 3F 2A 00"
MAC="AE FB CD 3E"
Config="00 00 00"
PIN="42035"
Immo Type="IMMO 4"
Immo Status="Immo OFF"


write new eeprom file to donor ecu and start car ok

[alfons37]

Thanks , have you pass :)

[alfons37]

Dont work, car crank but no start and glow lamp flash.

[ecuprogramer]

alfons37

My solution for cloning the ecu is good, first stop for a moment and think. When the car doesn't want the crank and glow plug lamp to see it's a problem until the car RALEY intelligent changes and the car starts ok..I think the mark raley 614 check is below the ecu black color

RALAY PROBLEM PLEASE CHANGE RALEY AND CAR START OK
(https://www.digital-kaos.co.uk/forums/member.php/76669-alfons37)

[alfons37]

But car crank but no start, car work with orginal ecu

[ecuprogramer]

here I made you an immo off solution if all raley are good the car should start and chk I calculated for you, write flash immo off and eeprom immo off

rep + thnx button

[alfons37]

Thanks have you pass, i have try 10-15 immo off solution but nothing work, but i can try your files. I think is bad ecu or another strange with with OTP area