Rav4 2006 immo problem after try add key

[castin]

Hi.
Im try add key to Toyota Rav4 2006 blade key - IMMO BOX: 89780-42110
Org key:
Tiris DST40
ID 67 Sub Key
P1: 92
P2: 02
P3: 8C 95 AB 0C
Im try add key use orange Toyota Smart Keymaker. After this, car don't start, key fob is ID67 DST40 like Sub Key. Now security led stay on, when im plug key in ignition, then blinking 2-3, org key blinking 2-2. Afte that im connect tango and try reset immo - no luck, get info "denaid Reset" and again "can't connect to ECU". Now SEC. LED stay on when car w/o key. Im try fast 5x cycle ign. on/off - no luck.
Please check dump from immo box, im add sec. key data:
P1: 32
P2: 88
P3: 72 34 A4 38
Thanx

[fred77]

heard some issue on tango forum. but why didn't u just clone?

add key takes 5 mins.

Anyway just restore eeprom - yeah

[ray-ray]

You must add 2 master first 4D67 (32 or 52) to close use valet logic 4D67 (92) light should go back normal. Sometimes is take 2 valet to close programming more common on Lexus.

[castin]

I don't now why im use this tool, in bag hawe tango with toyota activation, vvdi tool for clone and im use this orange tool. In check key and now i see - im try learn orginal sub key and new sub key, without master key. Maybe car wait for master key and dont end learn procefure. Im add to dump two sub key and master key. RayRay im prepare two master key and check on car. Can someone check dump - its correct?
P. S. In ecu hawe B2799 error, im try synchro, but use sub key and car not start. For synchro use sub or master key?

I found this info on Abrites site:
"
Important:
- Once you start the smart-key learning procedure do not close the driver side door or switch
the ignition off until a master key is not learned.
- Once immobilizer has been reset program at least two keys before next attempt for reset of
the immobilizer. If you try to reset the immobilizer while it is in key learning state it will be

destroyed permanently and you can fix it only by “Dump Tool”
- at least one MASTER key should be registered in the immobilizer system.
- MASTER key should first be programmed i.e. after reset of the immobilizer system the first
key programmed should be a MASTER
- In many cases immobilizers need registration of at least of two keys to finalize the learning
process

Now I know that I tried to reset the already reset driver in learning mode. Now the LED is on all the time, and when I insert the key, it flashes 2-2 or 2-1 (now I know that both keys were SUB-Key). Leave this dump eeprom or replace it with another dump, reset and sync?
Maybe it's enough to learn two Master Key now, then Sub Key?

[godfathertre]

Why did you just not cloned the transponder 2 minute job safe and trouble free.

[Manta1600]

Why did you just clone the transponder 2 minute job safe and trouble free.

Because isn't looks professional :)

but how proffessional looks when customer car can't start ?

[castin]

Why did you just clone the transponder 2 minute job safe and trouble free.

Heh, like sey Manta1600, but now im learn more ��.

[castin]

All OK, after add key by Tango car start at first time, no need synchro. Im add two SUB key and one master, car work on sub org. key and key fob (ID67 Tiris 4D Sub key). I think, if im try add MASTER key in lern mode, then all will be OK.