Mercedes crd3.10 flash help

[Pepesoft]

Hello.

Need some help with my file.
Kess V2 can`t id ecu at all.
Read flash with ktag,remapped it and no start. Have had trouble with ktag before (cheksum errors)
Tried to read with galletto v54 boot, reads 5% and makes error.
Can somebody take a look of flash and see whats wrong with it.
I would like to flash it with galletto so if possible to make changes to be able to flash katg read with galletto?
Or someone have ori bdm flash?
Car is mb c220cdi
HW:6519040001
SW:
SW upg : 6519039818
Installation : CRD3-651-WMA4B

Attached flash is original read by ktag, flashed it back and no difference. Propably bad read or something.

[figani]

Hello.

Need some help with my file.
Kess V2 can`t id ecu at all.
Read flash with ktag,remapped it and no start. Have had trouble with ktag before (cheksum errors)
Tried to read with galletto v54 boot, reads 5% and makes error.
Can somebody take a look of flash and see whats wrong with it.
I would like to flash it with galletto so if possible to make changes to be able to flash katg read with galletto?
Or someone have ori bdm flash?
Car is mb c220cdi
HW:6519040001
SW:
SW upg : 6519039818
Installation : CRD#-651-WMA4B


which ktag protocol you choose...?
808...?
or other...?

[Pepesoft]

Ktag protocol 808 was used reading and writing

[figani]

Ktag protocol 808 was used reading and writing

try to write by 809...

[Pepesoft]

Will try in a minute

Not possible. Ktag recognizes ecu as crd3.40 and forces to use protocol 808

[figani]

And if you put back ecu in car...
You can't reach ecu by kess...?

[Pepesoft]

Yep, when i install ecu on car fans spin full and no communication with ecu via obd.

[figani]

As you started with your operations...
Car was starting normaly...?
If yes, try to write ori back in boot mode...

[Pepesoft]

My friend brought me this ecu. Car was running fine before.
All he did was ID it with x17 and flash counter said : 1 so he tought it was already remapped.
Car came to garage to dpf/ egr delete.
Write back in boot mode with kess?
Same pinout as galletto? Solder 2 resistors to boot and cnf pins?

[figani]

Write back Ori by ktag if you don't has other tool...
And then not start car...
Only ignition and connect kess and try to make ecu ID...

Not possible by kess and boot...

[Pepesoft]

I tought so that kess don`t have boot.
Galletto won`t flash or read file in boot. Stucks at 5%.
Ktag reads and writes with no problem but doesn`t work.
I`m guessin that flash is corrupted, need ori flash from some place.

[figani]

I tought so that kess don`t have boot.
Galletto won`t flash or read file in boot. Stucks at 5%.
Ktag reads and writes with no problem but doesn`t work.
I`m guessin that flash is corrupted, need ori flash from some place.


just write by ktag ori...
connect it in car...
don´t start car gave only ignition...
connect ecu and make ecu id with kess...

and you´ll sove problem if ecu id work...

[Pepesoft]

Tried that already and no luck.
Shit, can't find ori anywhere with that software number.

[beltronics]

hello, does anyone have the frozen file of protocol 808 and 809? thank you