bmw e60 530d need more power please :3

[SyaXD]

Hey, I recently got in to this forum and would like to participate in it! My Kess v2 arrived today and would like to do some ecu tuning to my car:cupcake: If anyone could do some power (stage 1) without much blacksmoke I'd be so grateful, this file is stock all

[SyaXD]

edit: need also dpf and egr off :)

[SyaXD]

HW: 0281012091
SW: 1037379335
VIN nr.: WBANC71050B659293

[SyaXD]

and I wouldn't mind a popcorn tune @ 4500/5001rpms :)

[PelsonBMW]

Stage 1 for you , test and report

thx and rep after check

pass pm

[SyaXD]

Stage 1 for you , test and report

thx and rep after check

pass pm
Thanks. Going to test it now, was it dpf off ?

[SyaXD]

tested. sadly it didn't work :/

[PelsonBMW]

its only Stage 1 .

[PelsonBMW]

Flash your ori file , reset DPF values than upload my file .

same pass

[chrisimerk]

tested. sadly it didn't work :/

you need to reset dpf values with diag tool before writing modified file

[SyaXD]

Can ECMTitanium reset those dpf values?

[PelsonBMW]

Can ECMTitanium reset those dpf values?

Ds150 - Inpa - ista, ecm is tuning software

[SyaXD]

Cheers man

[SyaXD]

I ran into some problems, first time trying to reset dpf values is a little complicated to me, could someone write it off for me haha. I would really appreciate it <3

[chrisimerk]

I ran into some problems, first time trying to reset dpf values is a little complicated to me, could someone write it off for me haha. I would really appreciate it <3

we cant do it with file you need to reset dpf with a diagnostic tool such as delphi snap on solus and autel any of those tools will do even others.

write your ori back, hook up your diagnostic tool and reset dpf then write modified file, we cant help here its down to you mate

regards

[SyaXD]

Lmao lost my ori file how I get it back? all default

[PelsonBMW]

Your ori file is in your first post in this thread xD

You made my day right now :manutop:

[SyaXD]

Your ori file is in your first post in this thread xD

You made my day right now :manutop:

Lmfao and I have a the wrong cable, this shit doesn't support inpa XD

[PelsonBMW]

You have to use K+D can cable

[SyaXD]

You have to use K+D can cable

Hey, yeah I figured that out.
Today im going to give it another try since my irl friend has a inpa cable that I can use :p

[SyaXD]

Flash your ori file , reset DPF values than upload my file .

same pass
So I flash ori with kess, reset dpf adaptation value with inpa, flash ur egr dpf aofas file with kess and thats it?

[chrisimerk]

So I flash ori with kess, reset dpf adaptation value with inpa, flash ur egr dpf aofas file with kess and thats it?

yes thats it :encouragement:

[PelsonBMW]

He crashed his car of this power gain or bricked ecu xD that's why no response

[SyaXD]

He crashed his car of this power gain or bricked ecu xD that's why no response

Noo I just cant get it working at all, car is still in limp mode after trying to reset values and flashing ur file. The car still throws some dde (dpf) error codes.

[SyaXD]

I have only deleted dpf physically but the egr is still there and I haven't done anything to it, what should I do?

[SyaXD]

And after flashing with kess, sometimes transmission and stability control failure pops up :X

[PelsonBMW]

Dsc codes are related to angle sensor. Well hmm post Your dtcs here, How we can help if we dont Know what problems you have

[SyaXD]

Dsc codes are related to angle sensor. Well hmm post Your dtcs here, How we can help if we dont Know what problems you have

Its mostly like DDE errors, but will post dtcs here later today :D

[PelsonBMW]

Or try to flash file, reset dpf values. Instead if it still not work I will have to make another file , or you have disconnected dpf pressure sensor. It has to stay on its place with plug connected

[SyaXD]

Or try to flash file, reset dpf values. Instead if it still not work I will have to make another file , or you have disconnected dpf pressure sensor. It has to stay on its place with plug connected
Hello mate, Thanks for the tips.
I would think that a only dpf off file would fix the issue but idk.. been a little busy this weekend too lol, tomorrow I think I could have time to work with the car :)

[PelsonBMW]

your file dpf off stage 1....

[SyaXD]

your file dpf off stage 1....

Thanks mate, I tried to reset DDE/DME/Dpf values and clear dtc faults but with no luck, car is still in a limp mode..

[SyaXD]

Haven't tried your file yet Pelson but, will try later!