Elrasoft delivery time????

[florinyes]

Hi all

Just ordered a UPA-usb to find out it takes like 3 weeks to get it???? Anyone had any experience with them? At the end of the day Bulgaria is in eastern Europe not China. I've had chinese products delivered quicker. Are they placing an order to china as soon as someone placing a order with them? That could be the only explanation. Or, if they built in house, they have no stock and just looking to build one/some?

Hope fully the product is better than the service they provide.


Cheers

[kakkak66]

Hi I got only the programmer from elrasoft in this sec . It took 4 days to Ireland.
I did not get the Usb cable and software and manual.

[melmar]

i've bought a couple of programmers from elrasoft, and as you say it says 3 weeks, but if always been within the week, also as in above post its only been programmer, no leads or software or intructions.....

[florinyes]

Thanks

So leads should be ordered separately? Shouldn't they specify when you order that you need leads too? This is bo***x.

What leads suppose to came with? Is it just a usb lead?


Regards

[melmar]

haven't seen leads on there website, but have seen eeprom clips with leads on ebay, don't know what the quality is like, then you need some connecters for other end of lead, sorry i don't know the correct name is, but they are the 9 pin adaptors... somebody else will probably know a supplier if you post your location, in uk, i know maplins do them, but as i said i don't know where you are....

[florinyes]

Cheers bud

I am located in London..A link to Maplin please??

How about tacho universal cables? Will do the job?


Cheers

[kakkak66]

The usb cable just a simple USB printer cable. If you download the demo software the manual is in a HELP subdirectory.
http://elrasoft.eu/uuprog_demo.zip
But no driver for it. And no software. I asked them in email. But no answer until this time.
If you want adapters you should order separately. But only two exist.

[maciupiciu]

Sometimes U need to wait 3 weeks , but allways U will recive the programamer, also in the price of interface are included software application and future upgrades.
After U recive the hardware programmer write an email to support@elrasoft... and ask for .lic file
also U will get an username and a password to get access on elrasoft ftp were U will find last software version and other informations about adapters .
All adapters for eeproms need to be made it by U

[melmar]

www.maplin.co.uk (http://www.maplin.co.uk) the product code for the connector from lead into programmer is RK61R (its a D-sub connector), then do a search on ebay for eeprom clips with cables on... if you want a diagram of which wire goes where send me a pm and will help you out...

[florinyes]

Thanks everyone, very helpfull.

Still no answer to my question....will tacho universal cables be ok to use with UPA-USB?


Much apreciated!!!

[maciupiciu]

Thanks everyone, very helpfull.

Still no answer to my question....will tacho universal cables be ok to use with UPA-USB?


Much apreciated!!!

no, U can't use other cables, maybe just with some DIY adapters

[tachonow]

Except EEproms Upa is dastinate to work in circuit. No need no special cables just few wires as explain in help menu. Just read it.

[kakkak66]

I got the password for their homepage and i could download the software and manual.

[melcool]

Thanks everyone, very helpfull.

Still no answer to my question....will tacho universal cables be ok to use with UPA-USB?


Much apreciated!!!

Tacho Universal Clips work....but you have to make your own UPA to TU Clips adapter!
I will make you a picture whit them tomorrow!
......and use your imagination!

[Remapking]

Hi I have been told i require UPA-USB to read/write 908 chip (From Sprinter WSP unit) Is this correct, any advise would be more then welcome, Thanks

[florinyes]

Have a look in here mate ELRASOFT Products (http://www.elrasoft.com/uuprog.htm)

It sure does..

Ta

[BeianM]

Hi I have been told i require UPA-USB to read/write 908 chip (From Sprinter WSP unit) Is this correct, any advise would be more then welcome, Thanks

I am doing the same for the Espace dash & BII. I bought one from Elrasoft, it arrived in less than a week to the UK. Don't expect to get any help from them though. I have asked 3 times for support on adaptors & have not got a reply.
For me I think it would have been better to have bought the
ETL http://www.etlweb.com/?ref=products_programming_tools version that comes with adaptors. & if you mail them you can negociate on price.
I have ordered a clam type holder for the chip so I don't have to solder it to the adaptor & I see you can get one of these for the ETL.
Can anyone point me in the direction of articles regarding using this with the tacho universal, this would save me removing the chips & would be a great help, Thanks.
I'm off to do some searching about this.

[PremierD]

I am doing the same for the Espace dash & BII. I bought one from Elrasoft, it arrived in less than a week to the UK. Don't expect to get any help from them though. I have asked 3 times for support on adaptors & have not got a reply.
For me I think it would have been better to have bought the
ETL http://www.etlweb.com/?ref=products_programming_tools version that comes with adaptors. & if you mail them you can negociate on price.
I have ordered a clam type holder for the chip so I don't have to solder it to the adaptor & I see you can get one of these for the ETL.
Can anyone point me in the direction of articles regarding using this with the tacho universal, this would save me removing the chips & would be a great help, Thanks.
I'm off to do some searching about this.

First bit of research mate ..should be ..how to remove eeproms, so you don't fcuk them ......

[melcool]

Tacho Universal Clips work....but you have to make your own UPA to TU Clips adapter!
I will make you a picture whit them tomorrow!
......and use your imagination!

Here are the pictures whit the adapters:

[melcool]

As I said ..... use your imagination!

[BeianM]

First bit of research mate ..should be ..how to remove eeproms, so you don't fcuk them ......
Oh I have done plenty of that :) research that is & I have some boards to destroy. I did get a useful reply from elrasoft today, slow to do so however.

[florinyes]

Did anyone managed to build a box for the programmer? It looks exposed as it is..Elrasoft recommending this too..


Cheers

[maciupiciu]

a good friend of mine put his UPA in a box, here (http://www.mobile-files.com/forum/showthread.php?t=128189&page=2) can be seen some pictures

[adam28]

@florinyes (http://www.digital-kaos.co.uk/forums/members/109873-florinyes/)
You may want to get some of these too. 7" Female-Female Header Jumper : Store @ CuriousInventor.com (http://www.curiousinventor.com/store/product/196)

This company are in the US,but i use them a fair bit, with no probs. They have lots of of goodies here!

These are good for putting on the test clips and then to your programmer, and also on the pins of clusters etc. i cant get enough of these little buggers. And also the male type.

Cheers

[BeianM]

@florinyes (http://www.digital-kaos.co.uk/forums/members/109873-florinyes/)
You may want to get some of these too. 7" Female-Female Header Jumper : Store @ CuriousInventor.com (http://www.curiousinventor.com/store/product/196)

This company are in the US,but i use them a fair bit, with no probs. They have lots of of goodies here!

These are good for putting on the test clips and then to your programmer, and also on the pins of clusters etc. i cant get enough of these little buggers. And also the male type.

Cheers

I bought a pack of female crimp pins from Maplin & used insulation tape to wrap them as I couldnt find the small heat shrink. It does the job, not as good as ready made though. Thanks Adam I will keep them in mind.

[Remapking]

Have a look in here mate ELRASOFT Products (http://www.elrasoft.com/uuprog.htm)

It sure does..

Ta


Hi do you know which adaptor i would need to read 908 from merc wsp unit in circuit..

thanks

[BeianM]

The elrasoft that is discussed in this thred is designed to read in circuit. See if your chip is here => ELRASOFT Products (http://www.elrasoft.com/uusp.htm#uusp_supported_devices)

[florinyes]

if you want a diagram of which wire goes where send me a pm and will help you out...


Would you post the pin outs on the forum please. Got my UPs yesterday so within a week. The 3 weeks thing must be to cover them up.

Thanks everyone that had an input.

Best regards

[BeianM]

Would you post the pin outs on the forum please. Got my UPs yesterday so within a week. The 3 weeks thing must be to cover them up.

Thanks everyone that had an input.

Best regards

Did you login to elrasoft & get this? or do you still need it.

[BeianM]

Anyone here had any success with this programmer. I have been trying to read motorolla hc908's. Both on board & off, in a clamshell adaptor. I have not found any usefull help files for their software & tech support tells me to go read a different chip!! If there is a good forum you know of then let me know. I currently have it telling me I have an error of hi reset. Does not matter how many times I have checked the connections & have tried 3 chips. & how do you enter the security bits.
Thanks in advance.
(anyone got a tacho universal they want to rent me?)

[melcool]

Anyone here had any success with this programmer. I have been trying to read motorolla hc908's. Both on board & off, in a clamshell adaptor. I have not found any usefull help files for their software & tech support tells me to go read a different chip!! If there is a good forum you know of then let me know. I currently have it telling me I have an error of hi reset. Does not matter how many times I have checked the connections & have tried 3 chips. & how do you enter the security bits.
Thanks in advance.
(anyone got a tacho universal they want to rent me?)

What type of 908(Mask) and from what?!

[BeianM]

What type of 908(Mask) and from what?!

xc68hc08az60 qfp64 This mask set errata applies to this MC68HC08AZ60 MCU mask set: 1J35D (http://www.datasheetarchive.com/datasheet-pdf/018/DSA00309925.html)
http://www.freescale.com/files/microcontrollers/doc/data_sheet/MC68HC908AZ60A.pdf?WT_TYPE=Data%20Sheets&WT_VENDOR=FREESCALE&WT_FILE_FORMAT=pdf&WT_ASSET=Documentation
it is dash & b11 from renault espace

[florinyes]

I do get grief to read eeprom too. Had a few 35080 and a couple of 93c and all zero's. Done a hardware test and it say 2 tests failed. Elrasoft saying the programer is OK. Just about to bin it...doing my head in..

Ta

[sl4ck]

Does UPA-USB package comes with software or not?

I have ordered UPA-USB, but don?t know if the package includes software or not, as i only see Demo version for download from ELRASOFT site.

[BeianM]

Does UPA-USB package comes with software or not?

I have ordered UPA-USB, but don?t know if the package includes software or not, as i only see Demo version for download from ELRASOFT site.

Write support an email to request your login & licence details. Log in to their site & you get the full version software.

[sl4ck]

where is login area?

can?t find it, really....

[florinyes]

Here it is mate

Please log in (http://www.elrasoft.eu/login.php)

Ta

[sl4ck]

I have no login yet, emailed to support asking for it.

[melcool]

I have no login yet, emailed to support asking for it.

ELRASOFT Support request support@elrasoft.com

[florinyes]

Yes mate comes with the sw but no adapters, usb cable or a power supply.

Ta

[BeianM]

Hi I have been told i require UPA-USB to read/write 908 chip (From Sprinter WSP unit) Is this correct, any advise would be more then welcome, Thanks

Yes that is what I am trying to do. The elrasoft may not be the best option. It is to be used with the chip in circuit. I have spent many hours trying to read this chip & banging my head against a wall. Curently have frame error showing. Waiting to hear from support to see where I'm going wrong. They recon It may not be poss to read this chip due to security settings.
May be better to buy the etl programmer as it is so much easier to remove the chip than messing around with a magnifying glass trying to solder to the legs of the chip. (in this case)
No doubt it will pay for it self reading other chips but at the mo 'the jury is out' !!!
Watch this space.

[sl4ck]

well support is sucking :(

i have already received my UPA but still waiting for login to get the software & licence details.

Can?t work without it...

[obdmaster]

Yes that is what I am trying to do. The elrasoft may not be the best option. It is to be used with the chip in circuit. I have spent many hours trying to read this chip & banging my head against a wall. Curently have frame error showing. Waiting to hear from support to see where I'm going wrong. They recon It may not be poss to read this chip due to security settings.
May be better to buy the etl programmer as it is so much easier to remove the chip than messing around with a magnifying glass trying to solder to the legs of the chip. (in this case)
No doubt it will pay for it self reading other chips but at the mo 'the jury is out' !!!
Watch this space.


M8 i chose clone xprog-m and i remove chips to program, my m8 PremierD says "sometimes you can damage other components if you dont remove" and that guy knows his stuff. Hes helped me loads, thanks premierD. Was looking at upa but dont like just getting programmer no adaptors etc. Glad i chose clone xprog-m as its been fine, no problems at all

[mec]

hi,
is somebody have for sale clip adapter for motorola 908 ?

http://t3.gstatic.com/images?q=tbn:cxTPkRxlcR3Q_M:http://www.elnec.com/pics/convert/con0147b.jpg (http://images.google.si/imgres?imgurl=http://www.elnec.com/pics/convert/con0147b.jpg&imgrefurl=http://www.elnec.com/products/device-programmers/socket-info/DIL48_TQFP64_ZIF_HC908-1/&usg=__NbzuzvyLascpHlLNWQ29_GanMUM=&h=221&w=300&sz=23&hl=sl&start=33&itbs=1&tbnid=cxTPkRxlcR3Q_M:&tbnh=85&tbnw=116&prev=/images%3Fq%3Dadapter%2Bmotorola%2Bhc908%26ndsp%3D2 1%26hl%3Dsl%26sa%3DN%26start%3D21)

thx,m

[melcool]

hi,
is somebody have for sale clip adapter for motorola 908 ?

http://t3.gstatic.com/images?q=tbn:cxTPkRxlcR3Q_M:http://www.elnec.com/pics/convert/con0147b.jpg (http://images.google.si/imgres?imgurl=http://www.elnec.com/pics/convert/con0147b.jpg&imgrefurl=http://www.elnec.com/products/device-programmers/socket-info/DIL48_TQFP64_ZIF_HC908-1/&usg=__NbzuzvyLascpHlLNWQ29_GanMUM=&h=221&w=300&sz=23&hl=sl&start=33&itbs=1&tbnid=cxTPkRxlcR3Q_M:&tbnh=85&tbnw=116&prev=/images%3Fq%3Dadapter%2Bmotorola%2Bhc908%26ndsp%3D2 1%26hl%3Dsl%26sa%3DN%26start%3D21)

thx,m

See here! Register for the prices!
Adapters,Auto Chips-OBDAUTO--BMW OPS VAG-COM,Tacho Universal,KWP2000,BMW Scanner,BMW Carsoft,ELM323,Code Reader,Can-bus (http://obdauto.com/nsort.asp?sort_id=10&nsort_id=94)

[mec]

See here! Register for the prices!
Adapters,Auto Chips-OBDAUTO--BMW OPS VAG-COM,Tacho Universal,KWP2000,BMW Scanner,BMW Carsoft,ELM323,Code Reader,Can-bus (http://obdauto.com/nsort.asp?sort_id=10&nsort_id=94)

thanks for links,m

[melcool]

thanks for links,m

You are welcome my friend!

[sl4ck]

need help...

Elrasoft support don?t answear to me and i need Software and drivers to use UPA-USB

[Smac_a]

Hello everybody!:ciao:

A couple of days ago I was trying to program a 93c66 onboard srs module and almoust gave up trying lifting the pins to make it work (and hopping it will still work later:dontknow:). Now i see that all you guys simply desolder the mcu or eeprom and solder it back on when it's all done.
Does anybody lift/cut pins? How do you know which one to lift?

thx,
Smac

[melcool]

need help...

Elrasoft support don?t answear to me and i need Software and drivers to use UPA-USB

Take form here sl4ck ... but when you will receive the email from Elrasoft please replace the uuprog.lic from the UPA/dir with yours!
MEGAUPLOAD - The leading online storage and file delivery service (http://www.megaupload.com/?d=UFB8XNFG)

[sl4ck]

Thanks melcool, received email this afternoon.

[bolonc]

My adapter

[BeianM]

M8 i chose clone xprog-m and i remove chips to program, my m8 PremierD says "sometimes you can damage other components if you dont remove" and that guy knows his stuff. Hes helped me loads, thanks premierD. Was looking at upa but dont like just getting programmer no adaptors etc. Glad i chose clone xprog-m as its been fine, no problems at all

If you remove the chip it needs a circuit + the crystal. So only other way is the etl 908 programmer. Different for other devices though.

[obdmaster]

If you remove the chip it needs a circuit + the crystal. So only other way is the etl 908 programmer. Different for other devices though.


Dont think it does read manual attached page 18

[BeianM]

Dont think it does read manual attached page 18

Thanks, It is the same as what is in the elrasoft help file however this is the reply from tec support.


> me > At the moment I get 'high reset'

tech reply >
the programmer can not put reset in '1' because the MCU hold this pin = '0'


You get this error when

- Reset pin circuit does not allow programmer to drive MCU Reset pin

in this case lift MCU Reset pin and connect P7(programmer) direct to this pin

- There is a MCU oscillator fault - no clock on EXTAL-XTAL MCU pins

now check quartz resonator or external oscillator - in some cases you have to power all target board by external power supply

in this cases do not make connection P9(programmer) -> Vdd(MCU)


What you've done:

you've desoldered the chip and trying to read

you've connected a crystal to XTAL - EXTAL ->good

but according device datasheet you have to connect a 10Mohm resistor to XTAL-EXTAL too

also you have to connect additional components to some pinso the MCU can work

see attached schematic of hc08 adapter

As you see it's not enough to make a few connections to the chip and to get success reading

MC68HC08AZ60 MCU mask set: 1J35D (http://www.datasheetarchive.com/datasheet-pdf/018/DSA00309925.html)

1J35D this device has additional eeprom protection

it is not supported by this programmer if this protection is ON

In most cases trying to read a protected hc908:

eeprom area will read ADs only not real data
> tech support end.

So If there is anyone out there that knows the magic answer to reading this chip onboard with this programmer, please step forward :)

[pirilla]

Hello, I have ordered UPA-USB from Elrasoft.

I have received order confirmation, but in email they only talk about software delivery but not about programmer (hardware), and in invoice only appears "UPA-USB Device Programmer Software". I understand that it includes the programmer, because when I placed order it appear like a "pack".

Is this normal???

I'm worry about buying only software, but I think it would be not reasonable.

Thank you.

[BeianM]

How much did you pay? This is the link for the programmer & software => share*it! - A service of Digital River (DEF03) - UPA-USB Device Programmer Software - UPA-USB Device Programmer Software, High-Speed USB Module, UPA-USB Serial Prgrammer (http://shareit1.element5.com/programs.html?productid=300039877)
If you made a mistake then let them know asap & ask for the order to be updated.

[pirilla]

This is what I payed, so I supose my order is right.

I will email them and ask for order information.

Thank you.

[media]

Hello, It's normal. This is the procedure. You will receive the programmer by post and the licence file for the software by e mail.

[pirilla]

Thank you media.

That is what i suposed, but email is not so clear.

[mastaflex]

hello all:

programmer takes no less than 3 weeks and software + licence are sent by mail

[pirilla]

Take form here sl4ck ... but when you will receive the email from Elrasoft please replace the uuprog.lic from the UPA/dir with yours!
MEGAUPLOAD - The leading online storage and file delivery service (http://www.megaupload.com/?d=UFB8XNFG)

I have received my programmer, but still don't have reply from support.

Can I use this software before they send me my license key???
Or must programmer and key match???

Thank you.

[Motika]

Yes you can. Thats what i did and i never had any problems.

[pirilla]

Yes you can. Thats what i did and i never had any problems.

Thanks, but... what about drivers???

[BeianM]

Hello everybody!:ciao:

A couple of days ago I was trying to program a 93c66 onboard srs module and almoust gave up trying lifting the pins to make it work (and hopping it will still work later:dontknow:). Now i see that all you guys simply desolder the mcu or eeprom and solder it back on when it's all done.
Does anybody lift/cut pins? How do you know which one to lift?

thx,
Smac

This programmer is sold as an 'onboard programmer' so for many devices that need a clock or rely on another circuit you are supposed to power up the board seperatley. For simple devices then yes you can remove it from its board. Some people prefer to cut the circuit rather than lift the legs. Hope you get to grips with it. The pdf manual shows dotted lines but don't believe that you are supposed to lift these. You are best to do some research here or contact support.

[BeianM]

See here! Register for the prices!
Adapters,Auto Chips-OBDAUTO--BMW OPS VAG-COM,Tacho Universal,KWP2000,BMW Scanner,BMW Carsoft,ELM323,Code Reader,Can-bus (http://obdauto.com/nsort.asp?sort_id=10&nsort_id=94)

I don't think these adaptors are going to be any good to you without a clock circuit. As per my earlier post, I bought one & tried it with no success. UPA-USB is an 'on board programmer' especially when you need other circuits to get the device to work.

[babilon]

Thanks, but... what about drivers???
contact support, they give you an user/password to access to the support page.
there you find, drivers(for USB),software , manual and some schemas.
about contact them, some days are fast,some days takes a week.

[BeianM]

(http://www.sinosells.cn/productshow.asp?id=2085&sortsid=3515&sorts=) Advertising removed
=
more details pls check
ship it to you in 2working days after you payment

If you can help people with relevent information on how to use devices then please do because this is what DK is for.
This is not an free advertisers board. If you wish to advertise your goods then please contact admin & pay for board advertising.

[km-digital]

hi all
Mr. Arthur of England sells adapters to read eprom circuit
hear some of this

[autocargo]

Hello everybody,I couldn't find a better place for my question. I have this Upa USB adapter for 24Cxx,25/95xxx,93Cxx,35080 eeproms. I don't have any documentation of this adapter and I did not found any info on forum or internet. I want to use it with my Upa programmer but not sure how. Do I solder eeproms to this adapter? Or is it enough if I just clip them to the board? Also there are some pins on top of adapter (10 pins exactly) it looks that you can bridge them or you can connect something there, I don't know exactly what....I'm sure somebody using this or has seen this adapter.Any help or documentation would be welcomed.
Thanks.

[Smac_a]

Hi.

Although the picture is quite blurry, I think it is meant to attach eproms directly on the board (dip on the top looks like it is a female adapter) or solder it (for the bottom two - soic and ?). For the ten pins on the top I don't have a clue - that is all I can see :).
Check with meter if connections from db-9 is the right one on the board. For example pin 5 goes to pin 1 on soic...

Smac_a


Hello everybody,I couldn't find a better place for my question. I have this Upa USB adapter for 24Cxx,25/95xxx,93Cxx,35080 eeproms. I don't have any documentation of this adapter and I did not found any info on forum or internet. I want to use it with my Upa programmer but not sure how. Do I solder eeproms to this adapter? Or is it enough if I just clip them to the board? Also there are some pins on top of adapter (10 pins exactly) it looks that you can bridge them or you can connect something there, I don't know exactly what....I'm sure somebody using this or has seen this adapter.Any help or documentation would be welcomed.
Thanks.

[autocargo]

Hello everybody,I couldn't find a better place for my question. I have this Upa USB adapter for 24Cxx,25/95xxx,93Cxx,35080 eeproms. I don't have any documentation of this adapter and I did not found any info on forum or internet. I want to use it with my Upa programmer but not sure how. Do I solder eeproms to this adapter? Or is it enough if I just clip them to the board? Also there are some pins on top of adapter (10 pins exactly) it looks that you can bridge them or you can connect something there, I don't know exactly what....I'm sure somebody using this or has seen this adapter.Any help or documentation would be welcomed.
Thanks.

I just managed to get better pictures. Anybody works with this adapter?

[Smac_a]

I just managed to get better pictures. Anybody works with this adapter?

I don't work with this adapter, I made my own one. But it looks ok. You could just try to program lets say 24c04. You can get these or 93cxx from old ethernet pci cards (mostly in soic form). Solder it in bottom socket (24c or 93c) and try reading it with UPA.

Smac

[autocargo]

I don't work with this adapter, I made my own one. But it looks ok. You could just try to program lets say 24c04. You can get these or 93cxx from old ethernet pci cards (mostly in soic form). Solder it in bottom socket (24c or 93c) and try reading it with UPA.

Smac

Thanks Smac. I will try it on, I guess is the only way to find out.Firstly I'm thinking just to clip the eeprom to board using the clips that my mum uses to hung clothing after washing. :laugh: It seems faster than soldering/unsoldering to board. If eeprom gets good contact with adapter pads it may just work :ridinghorse:
If anyone else has worked with this adapter please share your experiences.

[Amine13]

HI mates,
I bring my contribution and hope will help.
Here is the detailed file, showing how to make all adapters for EEPROMS, and where to solder wires for in circuit reading for MCUS Motorola.
Believe me, is very easy to make these adapters. Just you need is female /female RS232 cable, which you will cut in the middle, , with Multimeter you will specify each wire connection with female plug, this one hase numbers printed on the blue side showing each pin, they are also mentioned in the pdf document, all you have to is start your Solders !! :D

[autocargo]

Thanks Amine13. I already have that upa-usb pdf file. There is a tread about making your own adapters somewere on forum but since I got this adapter I was curious if someone has it,and if it is easier to work with this one rather than using the DIY adapter described by you. Anyway anybody got an idea about the 10 pins sticking out of this board? I have seen some ready made eeprom soic/clip adapters on ebay that are already wired and they have just the connector that will fit on top of that adapter.

[Amine13]

You can do it easily, all you have to do is to save the colors leads and their correspondance with RS232 female terminal; for example, the one I have is :
1: Black
2: brown...
I will try to upload some photos of the components you need to make an adapter from UPA ready to hold the eeprom directly.

[Amine13]

As promised here are some photos, all the components are availlable, you can find them easily, maybe for SOP8 adapter, you can get it through internet for less About 1500 Da ( 15?).
Sorry for the colors affectation, is in french. Then you can make just two cables with that, and when you need swiotch from SPI, I2C to Microwire, just unplug SOP8 adapter and put it on the other cable
Best Regards.

[autocargo]

Thanks Amine13. I ordered some 8 pin eeprom clip soic,it seems everybody is using them here and will make own leads using the cable you have on pictures. Now back to my adapter :)) I managed to find one 24C04 wich successfully read and program and one 24C02 that I mounted on adapter printed pads and secured with a clip my mum uses to hang clothes after washing :)) it needed a little extra pressure on the clip to achieve good contact with adapter pads and after that...... read and program successful!! No need to solder then. I've had some good times playing with this adapter. It seems it can be used safely to read and program. Didn't had other eeproms to test so only this two been tested with.

[morfej]

hi,

Does anyone managed to pay for UPA at share-it with paypal ?

When I suppose to be redirected to paypal website, just get message that order is delayed and nothing happens.

Share-it support is not helpful :( they just suggest to match billing email with paypal account email, but doesn't help either.

Br

[jimthejock]

hi there ive used share- it a couple of times to buy upa and it has worked fine, maybe there is a problem with the site at the moment

[morfej]

Did you used paypal or wiretransfer ?

I gave up with paypal and used wiretransfer to order UPA.

[jarfm]

My programmer arrived after 1 week. I've paid by PayPal. Now I'm waiting for login

[martij976]

I received my upa today (Nov-03-10) and waiting for software...
After sending an e-mail to support center, an automatic answer just let me know, that office is closed till nov-05 :o)
How cute....

[RossK]

Why the hell don't they just supply you a login with the device, I am waiting for mine to be delivered, and from the sounds off it, even when it does turn up I might have to wait another week for login, just so I can use it.

Seems to me by reading hundreds of posts that the hardware is good, but apart from that everything else sucks!

[datapage]

NEED SOFTWARE UPA USB Device Programmer v1.3.0.14
MY ORIGINAL INTERFACE.
THANKS

[Iggie]

In that case log in with your user and pass here: Please log in (http://www.elrasoft.eu/login.php)

[datapage]

bought used, do not have a password, I no have the User.
At the time, not sent to Brazil.

[mcm44]

If UPA programmer is original, write e-mail to support@elrasoft.com (support@elrasoft.com?subject=ELRASOFT%20Client%20 Center%20login%20trouble).
If serial number of device is ok, you will get username/password to log in. This version of software (1.3.0.14) have to be activated anyway in Elrasoft...

[ALVARES]

super adapter kit: http://www.ecuvonix.com/adapters-upausb-p-323.html (http://www.ecuvonix.com/adapters-upausb-p-323.html)