Motorola Cracker SW, please

[Zmann]

Hi Mates,
After more than a month-long spent trying with Motorola Cracker SW I dont get success with them at all, reset... reboot... reset... reboot forever! Can someone help me to a new try with the proved copies of them, it can be v4.3 and/or v6.2 or any. By the way, it has been proved that there is no problem with my MAX232 based interface , working fine. This is done by the other SW and the good Moto MCUs which using the similar interface. Many thanks.

[Car235]

Try to read on the board or removed MCU?
Which processor trying to read?
Post your schema interface.

[Zmann]

Hi Mates,
The MCUs tried are A8(QFP64,c96n),A1FN(PLCC52, D26E),E9(QFP64,E28B),811E2 (DIP,C16J),K4(PLCC84, D67F) and F1(PLCC68,F43V & only with other program) with on the boards and removed (with X-tal 4 or 8 Mhz connected). All are working fine, readable and programmable with other program which requiring the same interface but non with Moto Cracker I have. I built interfaces both the circuit of single MAX232 and the MAX232 with LS245, found on the net. I'm aware that there are some mislabel/minor mistake on the circuits but they were corrected during build up. Unfortunately I lack the know-how to use SW to redraw them. Both circuits are working with most combinations.
With the hope that the new copies of the SW will help me to verify the problem.

[Car235]

If you think that the problem of SW, here MotoCrack v6.2

[arturkob]

you're welcome
:top:

[Zmann]

Thank you mates. Try again with the v 6.0 and v7 ok from arturkob and v6.2 from car235 with all the MCUs, still no work. Restarts all the time but booting not success. I just think these SW copies are identical to the ones I have had. The v 7 ok is said to have some bug in it and I quite agree as the displayed EEPROM
address at least for A8 is wrong. I'm still quite sure that there is nothing wrong with my HW interface, MCUs and
the connection, retesting again with other SW is going well. Now, no more idea what are the puzzles behind. My PC is Pentium3 700 Mhz, XP SP3 and with the true RS232 com port. Mates, still need your help, any good trick from your experience to overcome this to share. Thanks.

[jcbs]

Hello.
And the schematic and conections ... can help me ?

Thank?s

[mikeslocks]

I have never had no problems with it what so ever you are not trying to use a usb to rs232 adaptor. UIt also works with other off the shelf hardware.

[sofix]

pullup R=1k to rx and tx to +5V

[prusony]

No comments.....

[prusony]

No comments_2

[milzal]

What HW is for reading HC912 with motocracker 7 ? On BDM pin must be any spliter for RX/TX to one BDM wire. Know anybody this HW ?

[Zmann]

Thank you all mates for the comments but even I try to +5V pull up to the RX and TX lines and with various versions of the SW all the results are of no change, the MCUs cannot boot up. This starts me to rethink on what any other possibility of fault on my boards even they works perfectly with the other two programs. Otherwise, should I give up and use other program instead.

[chana]

And what you are using the scheme you can show? just add the face values of all elements

[Zmann]

And what you are using the scheme you can show? just add the face values of all elements

The scheme in MOTOR2_3.9.RAR (http://www.digital-kaos.co.uk/forums/attachments/f115/10184d1264502841-motorola-cracker-sw-please-motor2_3.9.rar) by prusony should work, but I tried it with other similar program.

However, one more thing I would need to know. Can someone tell that all Motorola Crackers are compatible with Windows XP or not? Thanks.

[chana]

Thank you for the scheme. on work programs under OS WinXp just can not say. but I can say that the reset signal is exactly on any version of the program. I have one more question, if not remove the processor from the board and solder the wires only get to read and write memory??

[chana]

The scheme in MOTOR2_3.9.RAR (http://www.digital-kaos.co.uk/forums/attachments/f115/10184d1264502841-motorola-cracker-sw-please-motor2_3.9.rar) by prusony should work, but I tried it with other similar program.

However, one more thing I would need to know. Can someone tell that all Motorola Crackers are compatible with Windows XP or not? Thanks.

With this design, and program eprom can read and write, you can also read the ROM. the only thing that MC68HC05B16 legs 22, 11 - the level of logic 1. 19 feet 10 volts. 9 feet land. According to another processor will not enter treatment.

[Mac Gyver]

Motorola cracker sw works fine in win xp or in win 98 ???

[Zmann]

Motorola cracker sw works fine in win xp or in win 98 ???

You comfirm that the SWs work with both Xp and win98 or just ask.

I so far get no success with these SW of all ver. with my XP SP3. I now put the project in halt, put them in the drawer and wait to get the right win98 SW to try again. My slow lownload not allow me to get it from internet.

[Mac Gyver]

I'm asking, because I'm not had sucess in making this sw work, but not tested in win98.
please anyone friend could expose a more detailed explanation how to make this SW work with these interfaces RS232?

[jawier]

Somebody have the interface for prog. the HC912 :thumpdown:

[Dunker]

Some non read problems are because the IRQ line can't be pulled up to 10v. Monitor this as you try to read the MCU.

[Zmann]

HC11s do not need IRQ 10v. I've done lot of tries, the final suspect is the OS and it was in my last question. If you got success with them, it's better if you could
confirm of what the OS you got success with.

[jawier]

Hey, why the Motorola BDM v2 have a hex for atini2313 20Mhz and in scheme uses a at90s2313 at 10 Mhz.
This is fake?

[Zmann]

Hey, why the Motorola BDM v2 have a hex for atini2313 20Mhz and in scheme uses a at90s2313 at 10 Mhz.
This is fake?
I think you can no longer get at90s2313, it's too old. That's why attiny2313. Attachment might help.

[micromax]

hello, this is very simple interface to program hc912. this is clone of TMW inteface, work 100% in attach sw+hw

[jawier]

How can i know which is the Xtal in this 8l0 959 655 g (bosch 0 285 001 352)?:giveup:

[uk350]

maybe this one...

[Zmann]

That should be. But that is the type of a ceramic resonator replaced X-tal, I the first time see the ECU with a ceramic resonator instead of X-tal

[kasim_izmir]

How can i know which is the Xtal in this 8l0 959 655 g (bosch 0 285 001 352)?:giveup:
Hi , 16mhz is usually for hc912b32
Also , here is good dump

[jawier]

Thank you very much.:goodpost:
I tried to read it without success using Motorola cracker 7 but now i?m built a Hc912 TWM.
I must first built the PonyProg for the Attiny2313.:banghead:
Built a programmer for Attiny for built a programmer for Motorola.
BUF

[micromax]

you must build stk300 - http://www.lancos.com/e2p/avrisp-stk200.gif , work with ponyprog or icprog and its simple.

[monini64]

hello, this is very simple interface to program hc912. this is clone of TMW inteface, work 100% in attach sw+hw


can you upload in megaupload please?. thanks

[raptors]

Please atach PCB for TWM hc912 interface.

Thanks.

[jawier]

Here are a pack of motorola micros:wavey:

Hey, how can i configure the fuse bits for Attiny2313?
I dont understand.:hmmmm2:

MEGAUPLOAD - The leading online storage and file delivery service (http://www.megaupload.com/?d=0YUXVLSS)

[micromax]

check this fuse bits,
http://obrazki.elektroda.net/35_1233942467.jpg

[kautuvera]

How is this superpro u3000 can i configure the fuse bits for Attiny2313?

[jawier]

For example:

http://www.digital-kaos.co.uk/forums/attachment.php?attachmentid=21477&stc=1&d=1276241979

With 16Mhz original xtal.
It?s run perfect!!!!!:party ::party ::party ::party ::party :

[George Russo]

want to try if it crack i465

[jawier]

Hello, do someone know where found info about this project?:ridinghorse:

[Dacha]

Here's PCB and all you need my dear friends for making interface being discussed. Motorola kracker interface tested 100% working with UPA 2.3 software so if someone needs it can use this software!

[jawier]

Thank you so much, but, one question.:congrats:
Motorola cracker software for "Motokracker interface.rar"
and UPA 2.3 software for "BDM prog.rar"
Where do i find the dump for ATtiny2313?

[apostola]

help with fuses in pony for hc912 programmer

[SvetlinT]

Hi,
I need to program Mc68HC11A1.Please help me with suitable programmer.Thanks.

[pawel7924]

try UPA (connection included in doc),
giving external power
and lifting rx, dx, reset

[Gebrail]

No one tried to read mask CPU, like a 1K20C (MC68HC705B32)?

[Sayed Mamdouh]

I ask if this programmer can read eeprom of mc9s12dp512

[adrianvmx]

Can somebody help me with a schematic diagram based on MAX232N used for read/write an 68hc11ka4 MCU ? Thanks .