Citroen C4 JCI BSI sleep mode - cannot wake up

[DeLuXe]

Hi,

This is not the first time happening. But this is the first time that I cant communicate or connect to BSI on bench.
I'm hooked up with 12V - 2A charger even tried with car battery wich i usually used before.

Connected according to all diagrams I could find but still getting "Target does not respond" in FVDI.

BSI Information:
JCI
96 640 591 80 02
BSI04EV K05-00 280909
BOOT 28120836-4
HARD 281192496D

Tried with pictures attached without any success.

Any ideas?

Best regards,
DeLuXe

[hivrich]

maybe 6 - canH and 14 - canL

[DeLuXe]

Tried that as well my friend :/

Read somewhere that bsi need 3A 12V .. can anyone confirm ? No luck still, I think bsi is totally dead. If only had communication at least, damn..

Best regards
DeLuXe

[DeLuXe]

The BSI is totally bricked I'm right ?

Thanks

[momogsm]

Hi

Can You Confirm That Inside Bsi Eeprom 95128 And easyCAN4F1M32 In Processor

Regards

[DeLuXe]

Hi,

Yes there is 95128 eeprom and easyCAN4F1M32 MCU.

Best regards,
DeLuXe

[momogsm]

Hi,

Yes there is 95128 eeprom and easyCAN4F1M32 MCU.

Best regards,
DeLuXe
Hi

Then This Should Work, In Otherwise Your Bsi Is Bricked

Regards

[DeLuXe]

Tried that as well. BSI is dead, that's a shame :(
If I buy one used with same number can I transfer 95128 eeprom and car should start or do I have to virginie the bsi first ?

Weird that dashboard didn't have eeprom. How is it then possible to adjust mileage on this car? Thinking about the used bsi I will use that possibly will have higher mileage and write over dashboard.

Best regards
DeLuXe

[momogsm]

Tried that as well. BSI is dead, that's a shame :(
If I buy one used with same number can I transfer 95128 eeprom and car should start or do I have to virginie the bsi first ?

Weird that dashboard didn't have eeprom. How is it then possible to adjust mileage on this car? Thinking about the used bsi I will use that possibly will have higher mileage and write over dashboard.

Best regards
DeLuXe

Hi

Look When You Get An Used Bsi, Disconnect Plug From Dashboard, Then Plug Bsi In Car, See If ALL Work (Wipers, Signals...), If All Is Okay, Then You Need Lexia Diagbox To Telecoding The Bsi And Fvdi To Change Pin, And PIN From BOTH Bsi, We CAN Get It From 95128 Dumps,

If YOU Stuck I CAN Help Via Teamviewer, Just Write Me

Regards

[rafal]

momo wrote correct info...............just try to do what is posted by him

[DeLuXe]

Big thanks to you.
Problem is that I have lexia but have never used or installed it on my pc. I have PSA-COM (SuperScan).
I'm sorry but what is Telecoding ? Changing PIN code is possible with FVDI, shouldnt the car start if only to transfer data from 95128 chip? :)

Best regards,
DeLuXe

[momogsm]

Big thanks to you.
Problem is that I have lexia but have never used or installed it on my pc. I have PSA-COM (SuperScan).
I'm sorry but what is Telecoding ? Changing PIN code is possible with FVDI, shouldnt the car start if only to transfer data from 95128 chip? :)

Best regards,
DeLuXe

Hi

Not Possible To Swap Eeprom, Only If The Both Bsi Have The Same Signature, For Psa Com, I Don't THINK He Can Perform Telecoding, You Must Install Lexia It's The BEST in Psa Cars

Regards

[rafal]

or diagbox......................