HELP Renault Trafic 2015

[redonerj]

Hello , I have Renault Trafic 3 2015 with Ecu EDC17C42 0281031363
the car comes from us with problem lack of power


Diagnosis with abrites:


DTC0005: RAIL PRESSURE REGULATOR CIRCUIT


the fault is not ever removed




PS : Knowing that I am changed the pump and the regulation sensor in the common rail

i think the problem in ecu any help please


Thanks

[Louislesinge]

Hi,
Check power and signal on the pressure sensor, you should find with sensor disconnected: pin 1 ground / pin 2 Signal 5V / pin 3 Power 5V

Sensor is 1032 and goes to big black connector of the ECU.

With your Clip, to see what means the DTC definition check the white square box on the left of the DTC line!

Greetings,

[redonerj]

hello Louislesinge,
thank you for your interest, this is what I do not do I will try with that But I changed the high pressure kit (rail, pump, injector with its sensor) all the sensor when I disconnect the sensors i find another error code has appeared , I don't know which sensor gives this error I checked all the connector sensors up to ecu


It's an unreasonable problem

[Louislesinge]

Re,
Sorry, did not read very well your post, problem is on the regulator on the pump, not on the sensor!
So, on the pump there is only one regulator, this is number 1105. It's feeded under 12V from fuse F08 and negative command is on PIN2 from the ECU, big black connector PIN D4
First, with ignition ON connect 10W bulb between PIN 1 and ground, light should be full ON, if ok connect bulb between + batt and pin 2 (or between PIN 1 and 2 if 12V on PIN 1 ok): bulb should light ON lower than normally feeded.
Of course if command or +12V misses check continuity of the wires.
If all ok and DTC is permanent and can't be deleted or goes on every time you turn ignition ON, ECU should be out of order.
You can have a look at - Bosch repair service - (do Google search), there you can type your 0281XXXXXX number and watch what are the common failures...
Greetings,

[esse]

Hi,
if the whole mechanical part is good
I already had this problem after reading via OBD with original kess,
error is in eprom
I solved the problem with a dump of another calculator of same reference virginized and recoded immo etc
or go to dealer for update
in my case already last update in ecu

[redonerj]

Hi Louislesinge (https://www.digital-kaos.co.uk/forums/member.php/521396-Louislesinge)
Thank you for helping me with my problem, I check everything visible and check the continuity of the wires from the sensors to the unit everything is fine, I still have to test the frequency with oscilloscop but I have not given them,
thank you very much

[redonerj]

Hi esse (https://www.digital-kaos.co.uk/forums/member.php/120877-esse)

Thank you very much for participating on solution of my problem, I control all the mechanical part, is good, Your words are true and close to my problem I will follow in this direction
if you can help me, how i can do a update? if with CAN CLIP or other tools, and if you have a blank eprome


Thank you

[esse]

Hi,
post eprom file from ecu and i ll help you

[esse]

Yes you can with clip online or with the right update file from CD reprog

[redonerj]

Hello Esse Thank You
I have new news, when I wrote another EEPROM from another Renault, the error disappeared but without beginning because it is not eeprom own

[redonerj]

Yes you can with clip online or with the right update file from CD reprog
i don't have access can clip online , I can use Reprog v191 offline ?

[Louislesinge]

Hi,

i don't have access can clip online , I can use Reprog v191 offline ?

Yes you can, connect charger to car, disconnect CLIP from WIFI and try. But first ECU must be unlocked so you need to write original Eeprom.

Greetings,

[redonerj]

Hi,


Yes you can, connect charger to car, disconnect CLIP from WIFI and try. But first ECU must be unlocked so you need to write original Eeprom.

Greetings,
Hi Louislesinge (https://www.digital-kaos.co.uk/forums/member.php/521396-Louislesinge)
thank you
I will try this way, thanks for the help

[redonerj]

I have bad news i do reprog to the ECU But it stops at 11% and she didn't want to read after that read it just with boot mode any other solution, please

[Louislesinge]

Hi,
Try this:
Do you mean you lost communication with ECU?
If yes, is it reconized under reprogramming mode?
Go until Clip asks you to select ECU update, don't select it yet, turn ignition off, wait a few seconds, turn ignition ON and send update.

Battery must be over 12,70 (big charger or another car with engine running and jumped is required) , engine temperature must be under 60°.
Is your Trafic manual or automatic gearbox?
Greetings,

[esse]

Hi,
if not work post other eprom file from same ref and i ll transfert immo
i can t found free file

[redonerj]

Hi,
Try this:
Do you mean you lost communication with ECU?
If yes, is it reconized under reprogramming mode?
Go until Clip asks you to select ECU update, don't select it yet, turn ignition off, wait a few seconds, turn ignition ON and send update.

Battery must be over 12,70 (big charger or another car with engine running and jumped is required) , engine temperature must be under 60°.
Is your Trafic manual or automatic gearbox?
Greetings,
Hi Louislesinge Thank you for your reply yes i lost communication with the ecu , i read it with boot mode and returns to normal condition with error code and lack of power , I tried twice with reprog but he stop at 11 % and i lost communication with my ecu , i don't know where the problem if at reprog or can clip I do it with condition, with battery charger and temperature under 60 °

my traffic with manual transmission

[esse]

Hi,
if not found .....
http://www.ecubackup.com/renault-trafic-1-6dci-237105202r-0281031363-edc17c42-1037542560-1037543459
select soft version 1
BR

[redonerj]

Hi,
if not found .....
http://www.ecubackup.com/renault-trafic-1-6dci-237105202r-0281031363-edc17c42-1037542560-1037543459
select soft version 1
BR
Hello you got tired with me, I see some difference between my ECU, in the last four digits,

My ID :
HW: 3984R
SW: 1037547336
SW màj.: 5882R

if I buy this software what procedure should I do ? , Blank the new eeprom ?

[esse]

Hi,
in the eeprom I find
1037542560R
1037530693

the simplest is to post the file and I will transfer the immo

[redonerj]

OK Esse Thanks. I will do that soon

[redonerj]

Hi,
in the eeprom I find
1037542560R
1037530693

the simplest is to post the file and I will transfer the immo
hi esse sorry for the delay it's hard to find the eprome, i found an eeprom with a unit like him, please if you can help me
thanks

[esse]

Hi,
Try this one

[redonerj]

Hello Esse I have good news, the car went smoothly, I am very happy, the car that lasted more than a month today has started, I do not know how I can thank you :emmersed:
thank youuuuu very much
I have Ecudecoder plaese Please if you want any file anytime don't forget to tell me , This is the least I can do for you

[heralves]

HI.
I have a problem with eprom, can someone put a virgin or copy the immobilizer to an eprom in good condition.
The problem is that the car won't start.

[redonerj]

HI.
I have a problem with eprom, can someone put a virgin or copy the immobilizer to an eprom in good condition.
The problem is that the car won't start.
Hello , if the eeprom the same of my Ecu EDC17C42 0281031363 , se Esse can help you , if other Ecu better do new Post
Thanks

[heralves]

Redornej my Ecu is an Edc17c42 0281031364.

[redonerj]

There is a little difference, but I can send you the Eeprom that sent it to me Esse , it works fine

[esse]

There is a little difference, but I can send you the Eeprom that sent it to me Esse , it works fine

will not work...........
opel car...........
i ll have a look tomorrow at work

[heralves]

Thank you esse.
I am waiting, if you need any information please ask.

[esse]

Hi,
2 files..........
one with immo transfert
one with immo virgin
test and let me know

[heralves]

Hello again.
The car already gives the start thanks a lot!
Incredible work! Thank you very much! :)

[redonerj]

what Esse does, many people can't do, Esse does magic
Thanks

[heralves]

Truth.
This gentleman's good work is to be commended.
thanks

[esse]

what Esse does, many people can't do, Esse does magic
Thanks

all I know how to do now is thanks to what I learned on the DK forum.............
thanks to all member

[redonerj]

all I know how to do now is thanks to what I learned on the DK forum.............
thanks to all member
I wish you a great career

[aposig]

HI.
I have a problem with eprom, can someone put a virgin or copy the immobilizer to an eprom in good condition.

[Catalizator]

HI.
I have a problem with eprom, can someone put a virgin or copy the immobilizer to an eprom in good condition.

ori and mod eeprom

[hakimalarme]

827285HI all
i have the same problem esse can you help me

[redonerj]

Friends to find someone to help you with this problem , Please create a new post

[miz]

i have same problem make virgin or copy imoblizer .....i need help

[esse]

Hi,
Try this.....

[miz]

I'll try that tomorrow

[james44000]

I have same problem could you help me ? Thank you very much

[james44000]

Come on guys I’m blocked with this van
thank you

[kanishkaprasad]

ive got the same problem please can you help me out its an opel movano 2016 , i dont see fuel rail data pids . please help me

[oficina pereira]

Can anyone fix this eprom gives rail pressure error edc17c42 opel vivaro thanks