Which tool will read OL72A Chip

[super jumbe]

This OL72A chip how to read to get pin code thanks.

802770

[ollync]

Upa, xprog etl ..
Is it from opel immo? Then you can get pin with opcom from dash


Sent from my iPhone using Tapatalk Pro

[Andrnet]

This is the connection found by TNM5000 Programmer
Selection of A2C00038136-0L72A(ISP)
Programmer ISP Cable Connection:

Programmer Chip (64 pin) Chip(52 pin)

PIN1 PTA0=pin 26 pin 27
PIN3 RST =pin 3 pin 10
PIN5 PTC0=pin 60 pin 4
PIN9 IRQ =pin 2 pin 9
PIN10 GND =pin 21 pin 25
VCC =pin 22 pin 26
PTC1=pin61 pin5
PTC3=pin63

VCC must be connected to 5V.
PTC1,PTC3 pins must be low.

[lion0304]

This OL72A chip how to read to get pin code thanks.

802770


I read yesteday with Orange 5 clone Tigra immo. Need lift PDX, RXD and IRQ + Reset + GND and VCC.

Load dump in Tango, VVDI, Autel not recognise.

Only Effi match, but need test if it work.

[super jumbe]

Upa, xprog etl ..
Is it from opel immo? Then you can get pin with opcom from dash


Sent from my iPhone using Tapatalk Pro

Combo Van I can not read picode with opcom because the cluster is dead.
yes its from Vauxhall Combo Van 2008, I have already removed chip from cluster I think my best bet will be to order UPA-USB, is there another easy way to read thanks.

[Manta1600]

Combo Van I can not read picode with opcom because the cluster is dead.
yes its from Vauxhall Combo Van 2008, I have already removed chip from cluster I think my best bet will be to order UPA-USB, is there another easy way to read thanks.

Try to read the PIN with FVDI from ECU

Usually I read the pin code with old MVP clone but one month ago its stuck on one Combo and I read the pass with FVDI from the engine

[comizelu]

Try to read the PIN with FVDI from ECU

Usually I read the pin code with old MVP clone but one month ago its stuck on one Combo and I read the pass with FVDI from the engineMost of these combo are 1.3diesel, cannot read pin



Sent from my MI CC9 Pro Premium Edition using Tapatalk

[comizelu]

Combo Van I can not read picode with opcom because the cluster is dead.
yes its from Vauxhall Combo Van 2008, I have already removed chip from cluster I think my best bet will be to order UPA-USB, is there another easy way to read thanks.You can read bcm eeprom,will be easier.

Sent from my MI CC9 Pro Premium Edition using Tapatalk

[Manta1600]

Most of these combo are 1.3diesel, cannot read pin



Sent from my MI CC9 Pro Premium Edition using Tapatalk

If Im not wrong the van was exactly 1.3 diesel - And on the FVDI 2014 there is 2 versions I used the old version on the new version is not possible to read it

[super jumbe]

You can read bcm eeprom,will be easier.

Sent from my MI CC9 Pro Premium Edition using Tapatalk

This one is Vauxhall Combo Van 2008 1.7 Diesel, look when I replaced new cluster my opcom read and gave me the code, I think it may have read from the new cluster, when I tried to log in with the code the van is not accepting the code I read from new cluster, where is the BSI on this combo as far as I can remember the immo is in ECU, Cluster, Key reader, immobiliser unit next to battery.

[mikajna]

This one is Vauxhall Combo Van 2008 1.7 Diesel, look when I replaced new cluster my opcom read and gave me the code, I think it may have read from the new cluster, when I tried to log in with the code the van is not accepting the code I read from new cluster, where is the BSI on this combo as far as I can remember the immo is in ECU, Cluster, Key reader, immobiliser unit next to battery.

Yes, bcm have pin code to, its 93c46 or 93c56, that could be way to get pin code...or with some tool to read pin code from ecu carprog, fvdi...
upa uusp read this hc08 in circuit, only need to lift few legs as @lion0304 say

[comizelu]

1.7dti you can read pin by obd.
If you have pin from cluster just reset and program with opcom

Sent from my MI CC9 Pro Premium Edition using Tapatalk

[super jumbe]

I dont have original pincode from cluster, I have ordered UPA-USB and will read eeprom to get pin, and this van not got BCM.

[Manta1600]

I dont have original pincode from cluster, I have ordered UPA-USB and will read eeprom to get pin, and this van not got BCM.

1. Put the new cluster

2. Connect FVDI and read the pin from the Engine ECU

3. Connect Opcom go Instrument - eeprom and read the pin from the new cluster

4. then from Instrument - Programming - Reset IPC - enter the pin code from point 3

5 then Instrument - Programming - Program IPC - enter the pin code from point 2

all by OBD

[comizelu]

I dont have original pincode from cluster, I have ordered UPA-USB and will read eeprom to get pin, and this van not got BCM.Bcm is next to the battery somewhere.
Read pin from bcm.
You already have pin from new cluster,reset and program it..

Sent from my MI CC9 Pro Premium Edition using Tapatalk

[mikajna]

I dont have original pincode from cluster, I have ordered UPA-USB and will read eeprom to get pin, and this van not got BCM.
My friend, bcm is behind battery, remotes are programmed in bcm, every combo and corsa c have it.

[super jumbe]

Lads managed to read chip 93c66 & 93c66X16 BCM unit can someone help me out with pincode thanks.

[mikajna]

Lads managed to read chip 93c66 & 93c66X16 BCM unit can someone help me out with pincode thanks.

It should be 2530 my friend, try to log in bcm or immobiliser on car, and bcm and immo will tell you is it correct.
100% is that pin code.

Good luck