View Full Version : Bmw 525 won't start after flash
adamjay908
2nd May, 2021, 12:35 PM
Hi a friend of mine flashed his bmw 525d and it failed now the car won't start and can not read recovery via kess v2 any advice software is 1037390904
isavrseno
2nd May, 2021, 12:45 PM
i think you need to write more details about car and bricked ecu if you want to get better help
dehacko
2nd May, 2021, 12:53 PM
You must use K-tag and bdm frame backu up write. Maybe write ori map and car will start
erkor
2nd May, 2021, 12:54 PM
1.Correct checksum ?
2.Correct Isn ?
3.Synch ecu with Cas (ews).
adamjay908
2nd May, 2021, 12:54 PM
i think you need to write more details about car and bricked ecu if you want to get better help
Basically it was running someone went to remap it they read the file saved it then it failed and woulnt write then everytime they try to use recovery mode it fails and says wake up error
adamjay908
2nd May, 2021, 12:55 PM
Dose anyone have a ori file
Pyromaniak
2nd May, 2021, 12:56 PM
He mean how ecu you have, edc15 or edc16 or ecu number, how we have know how ecu you have in car.
Its edc16CP35
adamjay908
2nd May, 2021, 01:02 PM
i think you need to write more details about car and bricked ecu if you want to get better help
He mean how ecu you have, edc15 or edc16 or ecu number, how we have know how ecu you have in car.
Its edc16CP35
It's the BOSCH EDC16C35 sorry
jarvismaster
2nd May, 2021, 01:09 PM
I think this is a facelift e60 525D, which is EDC16CP35
And no more communicate via OBD
1. You need to remove the ECU, and open.
2. You need KTAG, and BDM frame or just directly solder the wires (or adapter) for the right pins
3. First try to read ECU via KTAG, because you original EEPROM content is important
4. Try to flash again your ECU via KTAG, just the FLASH that previously not worked with KESSV2 via OBD! and try with your car!
5. If this is not help, you need full BDM backup, and write all, but the EEPROM need to edit by someone that can help (your old ISN, Miles, Injector codes etc...)
Or write new ISN to EWS, and SYNC with ECU
adamjay908
2nd May, 2021, 01:13 PM
Probably a daft question but can u remove ews from coding
erkor
2nd May, 2021, 01:19 PM
I have this.
805968
adamjay908
2nd May, 2021, 01:20 PM
Thank you erkor
Pyromaniak
2nd May, 2021, 01:44 PM
make like jarvismater say, ews is in eeprom
peechie
2nd May, 2021, 10:05 PM
I think this is a facelift e60 525D, which is EDC16CP35
And no more communicate via OBD
1. You need to remove the ECU, and open.
2. You need KTAG, and BDM frame or just directly solder the wires (or adapter) for the right pins
3. First try to read ECU via KTAG, because you original EEPROM content is important
4. Try to flash again your ECU via KTAG, just the FLASH that previously not worked with KESSV2 via OBD! and try with your car!
5. If this is not help, you need full BDM backup, and write all, but the EEPROM need to edit by someone that can help (your old ISN, Miles, Injector codes etc...)
Or write new ISN to EWS, and SYNC with ECU
Dont write a OBD FLASH via KTAG...
Also you dont need to edit EEPROM,
Just write BDM FILE TO .FLS with KTAG and sync EWS-DDE/DME
andrimoto
3rd May, 2021, 09:40 AM
I had the same issue with opel insignia, i failed the write and the car couldn't start(with chinise kess). I solved it with recovery option. Connect the car use option recovery and write back the file you read from the car. Good Luck!
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.