Log in

View Full Version : Dash Renault Laguna2


mihai99
1st February, 2010, 11:09 PM
Hi , I need security bytes for read dash on Ranault Laguna 2003 1,9dtci, have mcu 68HC908AZ60 (1J35D).I use upa usb.
tachonow
2nd February, 2010, 12:40 AM
Hi , I need security bytes for read dash on Ranault Laguna 2003 1,9dtci, have mcu 68HC908AZ60 (1J35D).I use upa usb.
Sorry but this mcu is not secured
kioji41
2nd February, 2010, 07:13 AM
Hi , I need security bytes for read dash on Ranault Laguna 2003 1,9dtci, have mcu 68HC908AZ60 (1J35D).I use upa usb.

In dash of Laguna 2 only 1L02M mask is secured.
mihai99
2nd February, 2010, 09:36 PM
Thanks, probably need to cut some pins.
tachonow
2nd February, 2010, 10:04 PM
Thanks, probably need to cut some pins.
No. You dont need. Solder the wires as you see on upa help contents and job done.
Digamax
2nd February, 2010, 10:07 PM
Hi, You can use Licznik 4.0 and simple KL interface to do this dash via dash conector (2 minutes job), including 1L02M mask.

Best regards
Vladimir
kams20040
5th February, 2010, 12:40 PM
you tell 2 minutes job can you post a photo attachement how you do that please thank you
miki73
11th March, 2010, 06:47 PM
Hello! To Everybody.Please sombody have readed flash content from laguna 908az60 dash.I must replace chip..
Regards!(p.s. i have eeprom file)
tas_daz
12th May, 2010, 11:38 PM
how we conect the cables and what is kl interface please?i have upa can conect with upa cables?what is the rx and tx?
skcaki
13th May, 2010, 12:57 AM
There is a picture in licznik 4.0 with pinout and you can use i.e. KL interface with LM2903.
tas_daz
13th May, 2010, 04:04 PM
what is kl interface?see aphoto or where i can buy?>
the 409 vag intewrface it is good and what cable is power ground tx and rx?
jarfm
2nd August, 2010, 07:57 PM
Hi, can U explain me, how to doit with simple kl interface, please? From A to Z :idea:
Many thanx
jarfm
2nd August, 2010, 08:00 PM
Hi, You can use Licznik 4.0 and simple KL interface to do this dash via dash conector (2 minutes job), including 1L02M mask.

Best regards
Vladimir


Hi, can U explain me, how to doit with simple kl interface, please? From A to Z :idea:
Many thanx
tachonow
2nd August, 2010, 09:34 PM
This simple K-line interfaces work 100%.
jarfm
3rd August, 2010, 09:59 AM
This simple K-line interfaces work 100%.


OK, thanx. I gonna make one and try. To be sure, as I a understand, pin 17 of Laguna2 dash has to be connected to K-line of interface?
BeianM
3rd August, 2010, 10:42 AM
Maybe this will help. Laguna dash with upa.
Thanks go to member gopelhu (http://www.digital-kaos.co.uk/forums/members/116124-gopelhu/)

Digital Kaos - Downloads - HC08AZ60_1J35D_pinout (http://www.digital-kaos.co.uk/forums/downloads/car-dumps-database/34/hc08az60_1j35d_pinout-1259/)