View Full Version : Flashing ODO help please
kur715
28th September, 2021, 07:47 AM
Hi can someone help me with a 2011 holden colorado odo flashing after km change ,
eeprom 93A66 , read as 93C66 with digiprog3
837220
bmwparts
28th September, 2021, 08:15 AM
I would change 7F in very first entry to EE
kur715
28th September, 2021, 09:43 AM
Can i read it just as 93C66? or 93CS66?
bmwparts
28th September, 2021, 09:49 AM
Can i read it just as 93C66? or 93CS66?
With Digi3 I read as CS normally but doubt if it would make any difference.
kur715
28th September, 2021, 10:02 AM
ok great , does this look ok now?
837256
bmwparts
28th September, 2021, 10:09 AM
ok great , does this look ok now?
837256
Looks fine. Did you make a backup of original file before changing? If so post pic.
kur715
28th September, 2021, 10:11 AM
unfortunately no , rookie mistake and now I'm paying for it
Looks fine. Did you make a backup of original file before changing? If so post pic.
bmwparts
28th September, 2021, 10:18 AM
Happens. Just test and make sure odo ticks over.
kur715
28th September, 2021, 10:19 AM
will do , thank you
Happens. Just test and make sure odo ticks over.
kur715
28th September, 2021, 11:01 AM
for some reason this part doesn't837269 look right?
clusters
28th September, 2021, 11:24 AM
The whole file does not look good and will not work with just the one bye changed.
The remnants I see at 0000 and 0040-0043 are possibly part of a rolling VDO code. This is strange because this dash should be a Yazaki algo, same as Isuzu Dmax.
Post a picture of the dash label.
kur715
28th September, 2021, 11:31 AM
The whole file does not look good and will not work with just the one bye changed.
The remnants I see at 0000 and 0040-0043 are possibly part of a rolling VDO code. This is strange because this dash should be a Yazaki algo, same as Isuzu Dmax.
Post a picture of the dash label.
i think the dump is ruined
837276837277837278
clusters
28th September, 2021, 11:59 AM
Mileage would be 152005 Km, write these bytes to the file and try it.
0000: ee 22 ee 22 ee 22 ee 22 ee 22 ee 22 ee 22 ee 22
0010: ed 22 ed 22 ed 22 ed 22 ed 22 ed 22 ed 22 ed 22
0020: ed 22 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0030: 00 00 ff ff ff ff ff ff ff ff ff ff ff ff ff ff
0040: ff ff ff ff
kur715
28th September, 2021, 11:42 PM
No luck , changed as per above , still flashing odo
Mileage would be 152005 Km, write these bytes to the file and try it.
0000: ee 22 ee 22 ee 22 ee 22 ee 22 ee 22 ee 22 ee 22
0010: ed 22 ed 22 ed 22 ed 22 ed 22 ed 22 ed 22 ed 22
0020: ed 22 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0030: 00 00 ff ff ff ff ff ff ff ff ff ff ff ff ff ff
0040: ff ff ff ff
kur715
29th September, 2021, 10:59 AM
Hey guys , im trying to read the dash with ezp2010 to put new dump on but just get FF FF FF FF FF FF..... any reason why?
kur715
1st October, 2021, 12:17 AM
Thank you for your help , turns out the dump was corrupt , and my EZP2010 would not read the eeprom , i managed to get my Digiprog3 to communicate
to my PC , load a new dump , then write to the eeprom , tested and all is OK now.
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.